Replacing The Fuel Pump In Your 2007 Tacoma Truck

The fuel pump in the Toyota Tacoma is a device designed to pump fuel from the gas tank to the engine. When the pump goes bad, it stops pumping fuel to the engine, causing the truck to not start. The cost of replacing a fuel pump for a Toyota Tacoma is between $852 and $939, while the parts alone are priced between $694 and $740. This article will outline the steps to replace the fuel pump in a 2007 Toyota Tacoma.

Drain the fuel tank

To drain the fuel tank of your 2007 Tacoma, you will need a drain kit. This will include a hose. Insert the hose into your tank and pump the fuel to create a flow, and watch it drain. Keep a towel handy as there may be some spillage.

Safety is paramount when working with the fuel system. Take all necessary precautions to avoid the risk of fire. Ensure you are in a well-ventilated area and keep flames and sparks away from the work area.

It is also important to note that the fuel pump is located on top of the gas tank, so you will need to drop the tank to access it. This means you will need to remove the bolts holding the tank in place and place a jack under the tank to lower it slowly.

Once the tank is drained, you can move on to the next steps of removing the fuel lines, the fender liner, the inside bracket, and the fuel tank itself.

Remove fuel lines

To remove the fuel lines from a 2007 Toyota Tacoma, you will need pliers and a wrench. There will be lines connected to the sides and the front of the tank. Use your pliers to slide off the hose clamps, and for some lines, you will need a wrench to remove the line nuts. There will be some fuel drainage, so keep a towel handy.

It is important to note that before removing the fuel lines, you will need to drain the fuel tank using a drain kit. Insert the hose into the tank, then pump the fuel to create a flow, and watch it drain.

Additionally, after removing the fuel lines, you will need to remove the fender liner, inside bracket, and fuel tank before accessing the fuel pump.

Remove the fender liner

To remove the fender liner of a 2007 Toyota Tacoma, you will need a flat-head screwdriver and a socket.

First, use the socket to remove the bolts holding the fender liner in place. Then, use the flat-head screwdriver to pop off the clips holding the bottom part of the liner. You may need to apply some force to remove the clips, but be careful not to damage the fender liner or the surrounding components. Once all the clips are removed, push the liner out of the way.

If you are not planning on reusing the clips, you can simply rip them out or cut them with a sharp tool. However, if you want to reuse them, be careful when removing them to avoid damage. Alternatively, you can purchase replacement clips online or at an auto parts store.

It is important to note that accessing some of the clips can be challenging, especially those located towards the back, closer to the door. In some cases, you may need to remove nearby components, such as the corner light, to access the clips. Additionally, be cautious when working around the engine and fuel system to avoid any potential safety hazards.

Disconnect the battery

Disconnecting the battery is the first step in replacing the fuel pump in a 2007 Tacoma. This is a crucial safety precaution to reduce the chance of a fire when working on the fuel system.

To begin, locate the battery in the engine bay of your Tacoma. It is usually found near the front of the vehicle, on the side closest to the radiator. Once you have located the battery, look for the negative terminal, which should be marked with a "-" symbol. This terminal will have a black cable connected to it. Using a wrench or a socket, loosen the nut that holds this cable in place, but do not remove it completely yet.

The next step is to disconnect the positive terminal, marked with a "+" symbol and connected to a red cable. Again, loosen the nut with your wrench or socket, but do not remove it entirely. At this point, the battery should be disconnected, but it is good practice to check that the connections are secure and won't accidentally make contact.

Finally, you can carefully remove the battery from the vehicle. Place it in a safe location, away from any flammable materials, and ensure that it is secure and will not tip over.

Now that the battery has been safely disconnected and removed, you can proceed with the next steps of replacing the fuel pump in your 2007 Tacoma. Remember to exercise caution when working on any part of the fuel system to prevent the risk of fire or other hazards.

Install the new fuel pump

To install the new fuel pump, first, place the new fuel pump in the tank and tighten the bolts to secure it in place. Next, install the electrical harness on top of the tank.

Slowly raise the fuel tank back into place, ensuring you do not damage the electrical harness. Once the tank is in place, install the two brackets that hold the tank in position.

Reinstall the line on the driver's side of the vehicle and the bracket. Ensure the bracket is secured with two bolts.

Finally, secure the fender liner back into place.

Frequently asked questions