Replacing The Fuel Pump In A 2003 Mitsubishi Lancer

If your 2003 Mitsubishi Lancer is not starting, it could be due to a faulty fuel pump. The fuel pump is located inside the fuel tank and is submerged in the fuel. To replace it, you will need to remove the rear seat cushion and check for an access port. If there is an access port, simply disconnect the wiring, fuel lines, and unscrew the locking nut holding the fuel pump. If there is no access port, you will need to remove the fuel tank and then follow the same steps to disconnect and replace the fuel pump. Ensure you disconnect the battery and clean any dirt around the pump to prevent it from falling into the tank.

Check for an access port under the rear seat and trunk

To replace the fuel pump in a 2003 Mitsubishi Lancer, you'll first need to check for an access port under the rear seat and trunk. This is an important first step, as it will determine whether you can simply remove the pump or if you need to remove the fuel tank.

Start by removing the rear seat cushion. Once you've done that, check to see if there is an access port to reach the pump. Some Lancer models have an in-tank setup, so if you don't see the pump, you may need to drop the tank to access it. If you're unsure, you can refer to your Lancer's manual or seek advice from a mechanic or a Lancer forum online.

If you're unable to locate the fuel pump under the rear seat, don't panic. It's possible that your Lancer's pump assembly looks different, and the pump may be located in what appears to be a "mechanism" or "strainer-looking thing" as described by some Lancer owners. It's worth noting that the fuel pump assembly in the 2001 Lancer is located under the rear seat, so there may be some variation between model years.

If you do find the access port, simply remove the wiring to the pump, the fuel lines, and then unscrew the locking nut that holds the fuel pump in the tank. Remember to disconnect the battery before starting any work and to clean all dirt from the area to prevent it from falling into the tank.

Disconnect the battery

Disconnecting the battery is the first step to take when replacing the fuel pump in a 2003 Mitsubishi Lancer. This is a crucial safety measure as it prevents any electrical accidents or damage to the car's electrical system.

To begin, locate the battery in the engine bay. It is usually found near the front of the vehicle, close to the fender or firewall. Once located, identify the negative terminal, which is typically marked with a "-" symbol or a black cover. This terminal may also be thicker than the positive terminal, which is marked with a "+" symbol. Ensure that you do not confuse the two terminals, as disconnecting the positive terminal first can result in sparks or short circuits.

Next, you will need to loosen and remove the negative battery cable. This is usually secured with a bolt or clamp. Use the appropriate tool, such as a socket wrench or a combination wrench, to loosen the clamp. If the battery cable is tightly secured, you may need to apply some force to loosen it. Once loosened, carefully lift the cable away from the terminal, ensuring that it does not touch any metal parts of the car. Place the cable in a safe location, away from the battery, to avoid accidental reconnection.

With the negative cable disconnected, you can now proceed with the rest of the fuel pump replacement process, as outlined in other sources. It is important to note that you should not disconnect the positive cable unless absolutely necessary, as this could cause electrical issues or trigger the car's airbag system.

Remove the rear seat cushion

To remove the rear seat cushion of a 2003 Mitsubishi Lancer, start by checking under the rear seat to see if there is an access port to reach the fuel pump. If there is no access port, you will need to remove the fuel tank to access the pump.

If there is an access port, you can simply remove the rear seat cushion to access the pump. First, remove any screws or bolts holding the seat cushion in place. Then, lift the seat cushion and set it aside. Make sure to keep track of the screws or bolts so you can put the seat back in place later.

Once the rear seat cushion is removed, you should be able to see the fuel pump assembly. The pump is likely housed within the "mechanism" you see, which includes the float for the fuel tank indicator. To confirm, check for electrical connections leading to the pump.

If you need to remove the fuel tank to access the pump, make sure the gas tank is nearly empty before starting. Then, remove the bottom of the rear seat to access the fuel tank. This will involve removing any screws or bolts holding the rear seat in place and carefully lifting it out. Again, make sure to keep track of the screws or bolts for reassembly.

With the rear seat and cushion removed, you will have access to the fuel tank and pump for your 2003 Mitsubishi Lancer. Remember to exercise caution and refer to a professional mechanic if you are unsure about any steps in the process.

Disconnect the power supply socket and pipes

To disconnect the power supply socket and pipes of your 2003 Mitsubishi Lancer, you will need to follow these steps:

First, ensure that you have removed the rear seat cushion, as this is where the fuel pump is located. Once you have located the fuel pump, you will need to identify the power supply socket and the delivery and recovery pipes. These will be connected to the fuel pump.

Next, carefully disconnect the power supply socket. This will involve unplugging the power supply from the fuel pump. It is important to be gentle during this step to avoid damaging the socket or any surrounding components.

After disconnecting the power supply, you will then need to focus on the pipes. The fuel pump will have both delivery and recovery pipes attached to it. Identify these pipes and carefully detach them from the fuel pump. Ensure that you have a container or cloth ready to catch any fuel that may spill during this process.

Once the power supply socket and pipes have been disconnected, set them aside and ensure they are safely out of the way. You can then continue with the next steps of removing the fuel pump. Remember to be cautious and take your time during this process to avoid any damage to your vehicle or injury to yourself.

If you are unable to locate an access port, you will need to remove the fuel tank to access the fuel pump. It is important to disconnect the battery before beginning any work.

Unscrew the nuts of the fixing flange

To replace the fuel pump in a 2003 Mitsubishi Lancer, you will first need to locate the pump. Remove the rear seat cushion to check under the rear seat and trunk to see if there is an access port to reach the pump. If there isn't an access port, you will need to remove the fuel tank.

Now, to unscrew the nuts of the fixing flange, follow these steps:

• Disconnect the battery before you start working.
• If you have located the access port, simply remove the wiring to the pump and the fuel lines.
• Now, you can unscrew the locking nut that holds the fuel pump in the tank.
• Ensure that you clean all dirt and debris around the area where you are removing the pump to prevent any dirt from getting into the tank.
• Once the nut is unscrewed, the pump can be removed.

If you are unable to locate an access port, you will need to remove the fuel tank to access the pump. In this case, the process of unscrewing the nuts of the fixing flange will be similar, but you will first need to lower the fuel tank before you can begin disconnecting the wiring and fuel lines.

Frequently asked questions