Replacing Fuel Pump In Pontiac G6: Step-By-Step Guide

If you're experiencing issues with your 2008 Pontiac G6, you may need to replace the fuel pump. The fuel pump is responsible for delivering gas from the fuel tank to the fuel injectors, and problems with it can cause a loss of engine power or even prevent the car from starting. While it is possible to replace the fuel pump yourself, it is recommended that you let a repair shop handle this job due to the risk of fire. The cost of replacing the fuel pump can vary depending on your location, but it typically involves labour and parts costs.

Disconnect the battery

Disconnecting the battery is the first step when replacing the fuel pump on a 2008 Pontiac G6. This is a crucial safety measure to reduce the chance of a fire when working on fuel pump replacement.

To begin, locate the battery in the engine bay of your Pontiac G6. It is usually found near the front of the vehicle, on the side, or in a corner of the engine bay. Once you have located the battery, look for the negative terminal, which is usually marked with a "-" symbol or a black cover.

The next step is to loosen and remove the negative battery cable. You can do this by using a wrench or a socket that fits the bolt securely. Loosen the bolt carefully, turning it counterclockwise, until the cable can be removed from the battery terminal. Ensure that the wrench or socket is securely fitted to the bolt to avoid slipping and potentially causing damage to other engine components. Place the cable away from the battery to avoid any accidental contact.

After the negative cable is disconnected, locate the positive cable, marked with a "+" symbol or a red cover. Again, use a wrench or socket that fits securely on the bolt and carefully loosen it by turning it counterclockwise. Remove the cable from the battery terminal and place it away from the battery, ensuring it does not touch the negative cable or terminal.

With both cables now disconnected, you have successfully disconnected the battery. It is important to note that modern vehicles, like the 2008 Pontiac G6, may have multiple batteries or auxiliary batteries. If this is the case, simply follow the same procedure for disconnecting the additional batteries.

Remove the access cover

To remove the access cover of your 2008 Pontiac G6's fuel pump, you will first need to disconnect the battery to reduce the chance of a fire.

Next, locate the access cover. The fuel pump is usually inside the fuel tank, so the access cover will be above the tank in the passenger compartment. If there is no access panel, you will need to drain the fuel from the tank and then lower the fuel tank from the vehicle to access the pump.

Once you have located the access cover, remove it by unscrewing any screws or bolts holding it in place. Be sure to keep track of the screws or bolts so you can put them back in when you're finished. With the access cover removed, you will be able to access the fuel pump for replacement.

Replace the pump and pre-pump filter screen

To replace the pump and pre-pump filter screen of a 2008 Pontiac G6, you will first need to disconnect the battery to reduce the chance of a fire.

If the pump is inside the fuel tank, you will need to remove an access cover. With the cover off, you can replace the pump and pre-pump filter screen. In some cases, you will need to drain the fuel before removing the access panel.

If the pump is outside the tank, you will need to disconnect the fuel lines, remove the pump, and install the new one.

Once the pump is replaced, you will need to check for fuel leaks and ensure the problem is solved. It is recommended that you replace the fuel filters at the same time as the fuel pump.

Check for leaks

When replacing the fuel pump in a 2008 Pontiac G6, there are several steps to take to check for leaks. Firstly, the battery should be disconnected to reduce the chance of a fire. If the pump is inside the fuel tank, there will usually be an access cover that needs to be removed. In some cases, fuel will need to be drained before removing the access panel. Once the pump is exposed, the mechanic will remove the fuel pump supply and return hoses, as well as EVAP system hoses, and electrical connections.

After installing the new pump, the mechanic will re-establish all hoses and electrical connections, and add fuel to the tank. The engine is then run to test for leaks. The mechanic will check for fuel leaks or odors, and if any are detected, the car should not be started or driven, and it should not be parked inside a house or under a covered structure. Instead, the car should be towed to a shop for inspection and repair.

Replace the fuel filter

To replace the fuel filter on a 2008 Pontiac G6, you will first need to disconnect the battery to reduce the chance of a fire. Next, locate the fuel pump. This will either be inside or outside the fuel tank.

If the pump is inside the fuel tank, you will need to remove an access cover to reach it. In some cases, you will need to drain the fuel before removing the access panel. If the pump is outside the tank, simply disconnect the fuel lines and remove the pump.

Once you have accessed the fuel pump, you will also need to remove the fuel pump supply and return hoses, as well as any EVAP system hoses and electrical connections to the pump. If your fuel system uses an in-line external filter, this should be replaced at the same time as the fuel pump.

After replacing the fuel pump and filter, add fuel to the tank and run the engine to test for leaks.

Frequently asked questions