Rajan Wilcox
Resetting the fuel filter life on a Ram 3500 truck is a process that many owners have struggled with. Some have found success by scrolling to the fuel filter life page, pressing and holding the right arrow button, and then selecting reset, while others have had to resort to using a computer or taking their truck to a dealership for service. Some owners have also suggested driving the truck a few feet or disconnecting the battery cables to reboot the system. The specific steps to reset the fuel filter life may vary depending on the year and model of the Ram 3500, so it is recommended to consult the owner's manual or seek assistance from a qualified service technician.
Explore related products
What You'll Learn
Resetting a 2014 RAM 3500 6.7
- Scroll to the vehicle information page.
- Scroll to fuel filter life.
- Press and hold down the right arrow to select reset.
- When asked to confirm, scroll down to 'Yes' and press the right arrow button.
- This must be done with the ignition on and the engine off.
If this does not work, there are a few other methods to reset the fuel filter life. One method is to unhook the battery cables for about 10 minutes to reboot the system and then try resetting the fuel filter life. Another method is to perform a 4th Gen PCM reset. This can be done by following these steps:
- Remove the key from the ignition.
- Disconnect the negative battery cable.
- Put the key in the ignition and turn it as if you were trying to start the engine.
- Release the key and leave it in the "ON" position for 10-15 minutes.
- Remove the key from the ignition.
- Re-attach the negative battery cable.
- Start the truck and let it idle until it reaches operating temperature.
- Turn off the truck for 5-10 seconds.
- Re-start the truck and let it idle again.
- Turn off the truck and take it for a light test drive.
- Fire up the truck and drive as desired.
It is important to note that these methods may not work for everyone, and in some cases, it may be necessary to take the truck to a dealership or service centre for assistance.
Replacing the Fuel Filter in Your 2005 F150: Step-by-Step Guide
You may want to see also
Explore related products
Resetting a 2016 RAM 3500 6.7
Resetting the fuel filter life on a 2016 RAM 3500 6.7 can be a tricky process, and there are a few different methods that owners have reported success with. Firstly, it is important to note that this reset should be done with the ignition on and the engine off. One owner of a 2016 RAM 3500 6.7 reported that they were able to reset the fuel filter life by going to the vehicle info settings, scrolling to fuel filter life, and then pressing and holding down the right arrow to select reset. When asked to confirm, they scrolled down to yes and then pressed the right arrow button. This method involves a quick tap on the right arrow button after highlighting "yes".
Another owner of a 2016 RAM 3500 6.7 reported that they were unable to reset the fuel filter life using the method described above. They tried a variety of other methods suggested on forums and in the owner's manual, but nothing worked. They eventually took their vehicle to a dealership, where a service manager was able to reset the fuel filter life. The only difference in the process was that the service manager pressed the right-pointing arrow button after highlighting "yes" on the confirm reset screen.
It is worth noting that some owners have reported success with alternative methods. One owner suggested that after holding the reset button, driving the truck a few feet can help reset the fuel filter life. Another owner recommended unhooking the battery cables for about 10 minutes to reboot the system and then trying to reset the fuel filter life.
In addition to the above methods, there is another way to reset the oil life reminder on newer Dodge RAM models, which may be applicable to the 2016 RAM 3500 6.7. This method involves turning on the car by placing the ignition to "ON/RUN" without starting the engine. If the vehicle has a push-button ignition, press the "Engine Start/Stop" button twice without holding the brake. Then, push the accelerator pedal slowly three times in a 10-second interval and turn the ignition off. For push-button ignition, press the "Engine Start/Stop" button once without holding the brake. When the vehicle is started again, the oil life reminder should be reset.
Toyota Corolla Fuel Filter Clogging: Why and How?
You may want to see also
Explore related products
Resetting a 2015 RAM 3500
Resetting the Gas Cap Light
If the gas cap light on your 2015 RAM 3500 keeps coming on, you may need to replace the ESIM or the purge valve. The ESIM is a switch that monitors pressures in the evap system, and it can fail and is easy to change. To reset the PCM, you can either use a scan tool or disconnect the battery and touch both cables together before reattaching. Resetting the PCM is the only way to turn off the gas cap light.
Resetting the Fuel Filter Life
Resetting the fuel filter life on a RAM 3500 can be done by going to the fuel filter percentage on the dash and pushing the right arrow. This should give you the option to reset. This must be done with the ignition on and the engine off. Some users have reported that a quick tap on the right arrow button is required to reset the fuel filter life.
Resetting the Oil Life Light
To reset the oil life light on a Dodge RAM 3500, turn on the car by placing the ignition to "ON/RUN" without starting the engine. If you have a push-button ignition, press the "Engine Start/Stop" button twice without holding the brake. Then, push the accelerator pedal slowly three times in a 10-second interval and turn the ignition off. If you have a push-button ignition, press the "Engine Start/Stop" button once without holding the brake. When you start the vehicle again, the oil life reminder will be reset.
Resetting the RAM Computer
To perform a full reset of the RAM computer, you need to disconnect both battery cables and connect the ends to each other for at least 30 minutes or overnight. This is because there are numerous capacitors in the vehicle electrical subsystems that will hold a charge for a long time unless discharged, so simply disconnecting the battery may not do a full reset.
Changing Fuel Filter: 2003 S-10 Guide
You may want to see also
Explore related products
Resetting a 2021 RAM 3500SW
To reset the fuel filter life indicator, start by locating the fuel filter percentage on the dashboard. Ensure that you are looking at the percentage and not the service message. This step must be done with the ignition on and the engine off. Once you have located the correct section, push the right arrow button, which should bring up the option to reset.
Some users have reported that a quick tap on the right arrow button is sufficient, while others suggest holding down the button. If this does not work, you may need to refer to your owner's manual or seek assistance from a dealership. It is worth noting that some users have reported difficulties resetting the fuel filter life indicator, even with dealership assistance.
In addition to the fuel filter life indicator, there are other reset functions you may need to perform on your 2021 RAM 3500SW. For example, if you need to reset the tire pressure sensor, you can do so by following the instructions in your owner's manual or by using a scanning tool. If your vehicle uses a direct TPMS, you may simply need to push a reset button on the dashboard. On the other hand, if your vehicle uses an indirect TPMS, you will need to use a magnet or a scanning tool to reset the system. This can be done by a dealer or with a tool you purchase yourself.
Furthermore, if you encounter issues with your RAM 12-inch screen, there are a few troubleshooting steps you can take. For keyless start vehicles, push the start button twice without your foot on the pedal, and then hold down specific button combinations for 30 seconds. These combinations vary depending on your vehicle's features, but they generally involve the phone, voice recognition, tuner, or volume knob buttons. After releasing the buttons, turn the vehicle off, open the driver's side door, and wait 30 seconds before closing the door and restarting the vehicle. You can then access the dealer mode on the UConnect system to check for a reset option.
John Deere Fuel Filter: Maintenance and Inspection Guide
You may want to see also
Explore related products
![[Original] Waterdrop Filter Replacement for All Waterdrop Pitcher Filtration System, WD-PF-01A Plus, Reduces PFAS, PFOA/PFOS, Chlorine, Last Up to 3 Months or 200 Gallons (Pack of 3)](https://m.media-amazon.com/images/I/71Vbn7UTt-L._AC_UL320_.jpg)
Resetting a 2019 RAM 2500
Fuel Filter Life Reset:
To reset the fuel filter life on your 2019 RAM 2500, follow these steps:
- Turn on the ignition, but do not start the engine.
- Access the vehicle information system using the buttons on the left side of the steering wheel.
- Scroll to the fuel filter life option and select it.
- Press and hold the right arrow button to select reset.
- When asked to confirm, scroll down to 'Yes' and then press the right arrow button again.
- If this does not work, try driving the truck a few feet after holding the reset button.
Oil Change Reminder Reset:
To reset the oil change reminder on your 2019 RAM 2500:
- Turn the ignition to the 'ON' or 'RUN' position without starting the engine.
- Using the buttons on the left side of the steering wheel, access and select the vehicle information system.
- Scroll to find and select the oil life reminder system.
- Hold down the 'OK' button or the Right Arrow button until the oil life light resets to 100% on the dashboard display.
- Turn the ignition accessory button off.
Perform Service Indicator Reset:
To reset the perform service indicator on your 2019 RAM 2500:
- Turn the ignition switch to the 'ON' position without starting the engine.
- Press and release the brake pedal two times.
- Fully depress the accelerator pedal slowly two times within 10 seconds.
- Turn the ignition switch to the 'OFF' or 'LOCK' position.
It is important to consult your service manual and follow the vehicle manufacturer's recommended maintenance intervals and procedures.
Chevy Equinox Fuel Filter: What You Need to Know
You may want to see also
Frequently asked questions
Go to the vehicle information page and scroll to the fuel filter life option. Then, press and hold the right arrow button to select reset and confirm by pressing "OK".
Go to the fuel filter percentage on the dash and push the right arrow button. This should give you the option to reset. This must be done with the ignition on and the engine off.
With the engine off, turn the key to the 'On' position and push the reset button.
Try unhooking the battery cables for about 10 minutes to see if that will reboot the system and then try resetting it. Alternatively, try a quick tap on the right arrow button after highlighting "Yes" on the confirm reset screen.
![[Original] Waterdrop WD-PF-01A Plus NSF Certified Replacement Filters for All Waterdrop Pitcher and Dispenser Filtration System, Reduces PFAS, PFOA/PFOS, Last Up to 200 Gallons (4 Packs)](https://m.media-amazon.com/images/I/71Wd-ciC8qL._AC_UL320_.jpg)
