Craftsman Weed Eater: Replacing Fuel Lines, Step-By-Step

If the fuel lines on your Craftsman Weed Eater are blocked, bent, or split, you will need to replace them. Before you begin, ensure you have the necessary tools and safety equipment. You will need an approved fuel container, wire hanger (optional), paper towels or shop rags, and needle-nose pliers.

First, disconnect the spark plug wire and remove the fuel cap. Empty the fuel tank into the approved storage container. Next, locate and remove the fuel filter from inside the gas tank. Pull the fuel lines out of the tank, using needle-nose pliers if necessary. Cut the lines flush with the tank if they are difficult to remove. Now, tip the trimmer and shake out any remaining fuel line pieces.

To install the new fuel lines, cut the ends at an angle to make them easier to thread into the tank. Use needle-nose pliers to force the cut ends of the lines into the proper holes, pushing the larger vent line about an inch into the tank, and the smaller fuel supply line far enough so that the fuel filter will lay at the bottom.

Finally, reconnect the fuel lines to the carburetor, reattach the spark plug wire, and fill the gas tank with the fuel mix.

Disconnect the spark plug wire

Disconnecting the spark plug wire is one of the first steps to take when replacing the fuel lines on a Craftsman weed eater. Here is a detailed, step-by-step guide on how to do this:

Firstly, ensure that the engine is cool. The engine can be hot if the weed eater was recently in use, so it is important to allow it to cool down before proceeding. Once the engine is cool, locate the spark plug wire. It is connected to the spark plug, which is usually located near the engine. Grasp the spark plug wire firmly and pull it straight off the spark plug. This step is important for safety reasons, as it prevents the engine from accidentally starting while you are working on it.

It is also important to note that the spark plug wire is sensitive and can be damaged if not handled carefully. When pulling the wire off the spark plug, do so gently and avoid bending or damaging the wire. Additionally, make sure to pull the wire straight off, without applying excessive force or twisting it. By following these precautions, you can help ensure that the spark plug wire remains intact and functional.

After disconnecting the spark plug wire, set it aside in a safe place where it will not be disturbed. It is important to keep the area organized and tidy to avoid any mishaps during the fuel line replacement process. Once you have completed the fuel line replacement, you can then reconnect the spark plug wire to the spark plug. This will allow the engine to resume normal operation.

In summary, disconnecting the spark plug wire is a crucial step when replacing the fuel lines on a Craftsman weed eater. By following the steps outlined above, you can safely and effectively complete this part of the maintenance process. Remember to exercise caution and maintain a tidy workspace to ensure a smooth and successful fuel line replacement.

Remove the fuel filter

To remove the fuel filter from your Craftsman Weed Eater, you will need to locate the fuel filter inside the gas tank. It is a white cylinder attached to the end of the small fuel line. Use a pair of needle-nosed pliers or a straightened wire clothing hanger with a hook at the end to fish the filter out of the tank. Once you have a firm grip on the filter, simply pull it off the end of the fuel line.

If you are still unsure about the location of the fuel filter, it is attached to the small fuel line that runs from the carburetor into the fuel tank. The small line is the suction line from the tank, and the filter should be attached to the end inside the tank. It should be long enough to reach the bottom of the tank in any position.

If you are replacing the fuel lines, you will also need to disconnect the spark plug wire, remove the fuel cap and empty the fuel tank into an approved storage container, and disconnect the lines from the carburetor. Make sure you work in a well-ventilated area.

Disconnect the lines from the carburetor

Before disconnecting the fuel lines from the carburetor, it is important to take a digital photograph or make a diagram of how the fuel lines are configured between the tank and the carburetor. This will be useful when reconnecting the fuel lines.

To disconnect the fuel lines from the carburetor, use a pair of needle-nose pliers to remove the lines from the carburetor.

It is also important to note that before beginning any work on the fuel lines, you should disconnect the spark plug wire and empty the fuel tank into an approved storage container.

Pull the fuel lines out of the tank

To pull the fuel lines out of the tank, you will need needle-nose pliers or a similar tool to grip the lines. If you are unable to pull the lines out, you can cut them flush with the tank and use a small screwdriver to push the remaining sections into the tank. Then, tip the trimmer and shake it to remove any fuel line pieces that are left inside the tank.

Feed the new fuel lines into the tank

To feed the new fuel lines into the tank, start by cutting the ends of the new fuel lines at an angle. This will make it easier to thread them into the tank. Next, use needle-nose pliers, if necessary, to force the cut ends of the fuel lines into the proper holes in the tank. Push the larger vent line about an inch into the tank. Then, push the smaller fuel supply line into the tank, ensuring that the fuel filter will rest on the bottom of the tank. If the lines are tight, you can apply a small amount of oil to the outside of the line to make it easier.

Frequently asked questions