Replacing The Fuel Pump In Your Ep3 Civic: Step-By-Step Guide

Changing the fuel pump on a Honda Civic is a relatively simple task that can be completed in a few hours. The fuel pump is located under the rear seats and is accessible by removing the rear seats and the metal cover. Before beginning the process, it is important to ensure that there are no sources of smoke nearby as it could lead to a sudden fire or explosion. Once the fuel pump is exposed, the pump cover can be removed, and the pump can be disconnected and replaced. It is important to have a drip pan handy to catch any fuel that may drip from the fuel strainer. Additionally, it is recommended to refer to a step-by-step manual or video tutorial for a more detailed guide on changing the fuel pump.

Removing the backseats

To remove the backseats of a Honda Civic EP3, start by firmly grabbing both ends of the seat. Pull upwards to remove the seat, wiggling it as you do so. Take the seats out of the car to avoid damaging them. There are small latches on the front edge of the seat that you can use to help with this.

Once the seats are removed, you will be able to access the metal cover. Use a Phillips screwdriver to remove the four bolts that hold it in place. Then, tilt the cover out of the way to gain more access to the fuel pump.

Locating and removing the pump cover

To locate the pump cover, you must first remove the backseats of your Honda Civic. Grab both ends of the seat and pull upwards, wiggling it as you do so. Take the seats out of the car and put them somewhere safe to avoid damage.

Once the seats are removed, you will see a metal cover. This is the pump cover. Use a Phillips screwdriver to remove the four bolts that hold it in place, then tilt the cover out of the way to gain more access to the fuel pump.

Disconnecting the pump

Remove the backseats: The fuel pump in your Civic is conveniently accessible through the rear seats. Grab both ends of the seat firmly and pull upwards, wiggling it gently to remove it successfully. Remember to take the seats out of the car to prevent any accidental damage.

Locate and remove the pump cover: Once the rear seats are removed, locate the metal cover that shields the fuel pump. Use a Phillips screwdriver to carefully remove the four bolts holding the cover in place. After removing the bolts, gently tilt the cover out of the way to gain better access to the fuel pump.

Prepare the pump for removal: With the cover removed, you will notice several components that need to be detached before accessing the pump. First, slip off the boot covering the wiring connector. Then, use a suitable tool, such as pliers, to carefully remove the clamp on the rubber hose. Now, it's time to disconnect the main fuel line. This part requires caution as you will need to squeeze the fuel line to detach it. Lastly, use a 10 mm socket wrench to unbolt the bracket holding the pump in place.

Disconnect the pump: At this stage, you are almost ready to remove the fuel pump. Be cautious, as the fuel strainer may drip fuel. Place a drip pan underneath to catch any spills. Now, carefully grab the pump and pull it upwards to detach it from its housing. Once the pump is out, don't forget to disconnect the top plug and remove the strainer clamp.

Clean the area: Before installing the new fuel pump, it is essential to clean the area thoroughly. Use a suitable cleaning agent to wipe down the housing and ensure no dirt or debris remains. This step will help prevent any contaminants from entering the fuel system.

By following these steps, you will successfully disconnect the old fuel pump from your Honda Civic EP3. Remember to have a drip pan nearby to catch any fuel spills and always exercise caution when working with automotive fuel systems. Now, you are ready to install the new fuel pump and reconnect all the components.

Removing the strainer and replacing the pump

Now that the pump is disconnected, grab it and pull it upwards. Make sure your drip pan is nearby because the fuel strainer can drip fuel.

Once the fuel pump strainer is out, perform the following steps:

• Disconnect the top plug.
• Remove the strainer clamp.

Be careful not to drip any fuel while removing the pump strainer. The fuel pump is located inside the metal cylinder/canister.

You are now ready to install the new pump and connect everything back up.

Slide the new pump into place.

Reconnect the plug and fuel strainer.

Slide it back into the fuel tank opening.

Reinstalling the new pump

Now that you have removed the old fuel pump, you are ready to install the new one.

First, slide the new pump into place. Then, reconnect the plug and fuel strainer. Slide the pump back into the fuel tank opening. Bolt the bracket back in with the six screws to hold it in place.

Next, connect the fuel line and rubber hose. Plug the connector back in. Reattach the connector boot. Reattach the access cover with the five bolts. Finally, reinstall the back seat.

Frequently asked questions