Sylvie Willis
The fuel filter on a Toyota Supra is located on the driver's side of the engine, above a motor mount, and behind the stabilizer bar that goes from the engine block to the throttle body. It is a black canister with a metal banjo fitting on top and a banjo fitting on the bottom with a rubber hose attached. To access the fuel filter for replacement, one must first remove the pressure from the fuel lines by removing the tank cap and then pulling the fuse or electrical connection to the fuel pump.
Explore related products
What You'll Learn
- The fuel filter is located behind the driver's side front wheel
- It's above a motor mount on the driver's side of the engine
- It's behind the stabilizer bar that goes from the engine block to the throttle body
- It's in the fuel line tray located right underneath the car
- To access it, lift the carpeting in your hatch and remove the electrical connector controlling the fuel pump
The fuel filter is located behind the driver's side front wheel
The fuel filter on the Toyota Supra is located behind the driver's side front wheel. This is an incredibly inconvenient location, just above a motor mount on the driver's side of the engine. It is behind the stabilizer bar that goes from the engine block to the throttle body.
To access the fuel filter, you will need to jack up the driver's side of the car. You can then remove the 17mm bolt on the top that attaches it to the hard line, which goes to the fuel rail. After that, remove the 14mm bolts attaching the filter bracket to the engine block. It is important to brace the now loose filter against a flat surface in the engine bay so you can safely remove the bottom 17mm bolt.
It is recommended to replace the fuel filter with a genuine Toyota unit as part of routine maintenance. It is also important to note that most replacement fuel filters do not come with a protective "cage" like the OEM filter, so they will just hang" under the car.
Before replacing the fuel filter, it is necessary to relieve the fuel system's pressure. This can be done by removing the tank cap to release pressure in the tank and pulling a fuse or electrical connection to the fuel pump, then cranking the engine a few times.
Finding the Right Part Number for Ryobi BP42 Fuel Filter
You may want to see also
Explore related products
It's above a motor mount on the driver's side of the engine
The fuel filter on a Toyota Supra is located above a motor mount on the driver's side of the engine. It is situated behind the stabilizer bar that runs from the engine block to the throttle body. This location is specific to the 1982 model.
To access the fuel filter for replacement, you must first remove the pressure from the fuel lines. This can be done by removing the tank cap to release pressure in the tank and pulling the fuse or electrical connection to the fuel pump. You can then gain access to the fuel pump by folding back the carpet, removing a panel, and taking out the spare tire and access cover in the trunk.
Once the fuel pump is exposed, start the car and let it idle until it runs out of fuel. Then, jack up the driver's side to access the fuel filter. It is recommended to remove the 17mm bolt on the top of the fuel filter that attaches it to the hard line going to the fuel rail. After that, remove the 14mm bolts attaching the filter bracket to the engine block. Brace the now loose filter against a flat surface in the engine bay to remove the bottom 17mm bolt. With all bolts removed, you can take out the old filter from the bracket.
When installing a new fuel filter, be careful not to bend the hard lines. Use a wrench on both sides, and consider having an assistant for added ease.
Fuel Filter Lifespan: Mazda Tribute 2005 Edition
You may want to see also
Explore related products
It's behind the stabilizer bar that goes from the engine block to the throttle body
The fuel filter on the Toyota Supra is located on the driver's side of the engine, above a motor mount. It is in a rather inconvenient location, tucked behind the stabilizer bar that connects the engine block to the throttle body.
To access the fuel filter, you must first remove the 17mm bolt that attaches it to the hard line leading to the fuel rail. This is done to ensure that the hard lines are not bent during the removal process. It is important to be cautious and, if necessary, enlist the help of an assistant. Once the bolt is removed, the fuel filter bracket is exposed, and the next step is to remove the bolts attaching it to the engine block. There are two 14mm bolts that need to be taken out.
With the bolts removed, the fuel filter is now loose and can be carefully braced against a flat surface within the engine bay. This step is crucial to gain access to the bottom bolt of the filter. After removing the final 17mm bolt, the old filter can be taken out of the bracket.
When installing a new fuel filter, it is essential to follow the above steps in reverse. Pay extra attention to ensure that the hard lines are not bent during the installation process. A wrench can be used on both sides, and if needed, don't hesitate to have someone assist you.
It is recommended to replace the fuel filter with a genuine Toyota unit as part of routine maintenance. This is especially important as your Supra gets older.
How Water Gets into Your Fuel Filter
You may want to see also
Explore related products
It's in the fuel line tray located right underneath the car
The fuel filter on the MK3 Supra is located in the fuel line tray, which is positioned directly underneath the car. This is just below the seating area, on the underside of the vehicle.
To access the fuel filter for replacement, you will need to first remove the pressure from the fuel lines. This can be done by removing the tank cap to release the pressure in the tank. You can then pull the fuse or disconnect the electrical connection to the fuel pump, before cranking the engine a few times.
Next, lift the carpeting in the hatch to expose the electrical connector that controls the fuel pump. With the connector in sight, turn on the car and let it idle until the fuel in the lines is depleted. At this point, you can jack up the driver's side of the car to access the fuel filter.
The fuel filter itself is located behind the driver's side front wheel, above a motor mount. It sits behind the stabilizer bar that runs from the engine block to the throttle body. To remove the fuel filter, you will need to first remove the 17mm bolt that attaches it to the hard line leading to the fuel rail. Then, remove the 14mm bolts securing the filter bracket to the engine block. With these bolts removed, carefully brace the now loose filter to prevent any damage to the hard lines. Finally, remove the bottom 17mm bolt and the old filter can be taken out of the bracket.
When installing the new fuel filter, be cautious not to bend the hard lines. It is recommended to use a wrench on both sides and have an assistant for added safety.
CarQuest Fuel Filter: Audi's Performance Enhancer?
You may want to see also
Explore related products
To access it, lift the carpeting in your hatch and remove the electrical connector controlling the fuel pump
The fuel filter on a Toyota Supra is located in the fuel line tray, underneath the car, just below the driver's seat. It is on the driver's side of the engine, above a motor mount, and behind the stabilizer bar that goes from the engine block to the throttle body.
To access the fuel filter, you must first remove the pressure from the fuel lines. This can be done by removing the tank cap to release the pressure in the tank and pulling the electrical connector controlling the fuel pump. To do this, lift the carpeting in your hatch to reveal the connector, which can be found on a foam piece. Once the connector is removed, turn on your car and let it idle until it runs out of fuel. Then, jack up the driver's side to access the fuel filter.
Before removing the fuel filter, it is recommended to remove the 17mm bolt on the top that attaches it to the hard line which goes to the fuel rail. Then, remove the 14mm bolts attaching the filter bracket to the engine block. Brace the now loose filter against a flat surface in the engine bay so you can remove the bottom 17mm bolt. Now, you can remove the old filter from the bracket. Reinstallation is the reverse of this process, taking care not to bend the hard lines.
It is recommended to replace your factory fuel filter as part of routine maintenance, especially as your Supra gets older. It is also wise to change your fuel filter every 30,000 miles, or more often depending on your driving habits.
Inspecting Fuel Filters: Signs of Dirt and Damage
You may want to see also
Frequently asked questions
The fuel filter is located on the driver's side of the engine, above a motor mount. It is behind the stabilizer bar that goes from the engine block to the throttle body.
You can access the fuel filter by removing the pressure from the fuel lines. First, remove the tank cap to release the pressure in the tank. Then, remove the fuse or electrical connection to the fuel pump and crank the engine a few times.
To replace the fuel filter, first remove the 17mm bolt on the top that attaches it to the hard line. Then, remove the 14mm bolts attaching the filter bracket to the engine block. Brace the now loose filter against a flat surface in the engine bay and remove the bottom 17mm bolt. Finally, remove the old filter from the bracket.
