Resetting The Fuel Filter Light In Your 2008 Express Van

If you're wondering how to reset the change fuel filter light on your 2008 Chevrolet Express van, you've come to the right place. This tutorial will walk you through the steps to reset the fuel filter light and get your van back up and running. It's important to note that resetting the fuel filter light is different from resetting the oil change light, which is a separate process that we can also guide you through.

Resetting the fuel filter monitor on vehicles with steering wheel controls

• Press and hold the "Select" button on your steering wheel controls for approximately 5 seconds. Ensure you do this while the "FUEL FILTER LIFE" message is displayed on the driver information center (DIC).
• The "FUEL FILTER LIFE" message will be displayed for about 10 seconds.
• After releasing the button, the system will now be reset.

Always remember to reset the "FUEL FILTER LIFE" system after changing the fuel filter. This ensures that your vehicle's maintenance schedule remains accurate and up-to-date.

If your vehicle does not have steering wheel controls, follow this alternative method:

• Turn the ignition key to the "ON" position without starting the engine.
• Fully press and hold both the brake and accelerator pedals simultaneously for 10 seconds.
• Release the pedals and turn the ignition key to the "OFF" position.
• The next time you start the engine, the "FUEL FILTER LIFE" message will no longer be displayed.

Resetting the fuel filter monitor on vehicles without steering wheel controls

• Without pressing any pedals, turn the ignition key to the "ON" position without starting the engine. Ensure the vehicle is in park and the parking brake is engaged for safety.
• Wait for about five seconds. This pause is essential to allow the system to initialize and recognize the upcoming reset procedure.
• Now, simultaneously press the brake and accelerator pedals completely and hold them down together for about 10 seconds. This step is crucial for successfully resetting the fuel filter monitor.
• After holding the pedals down for the full 10 seconds, release them and turn the ignition key to the "OFF" position.
• The next time you start the engine, the "Change Fuel Filter" message should no longer be displayed, indicating that the system has been successfully reset.

Remember, it is important to reset the fuel filter monitor each time you change the fuel filter. This ensures that your vehicle's systems are accurately calibrated and functioning optimally.

Resetting the oil change light with the DIC button

Firstly, insert your key into the ignition and turn it to the 'on' position. It is important that you do not start the engine. For vehicles with steering wheel controls, press and hold the 'select' button for 5 seconds while the "FUEL FILTER LIFE" message is displayed. This message will appear on the driver information center (DIC) for 10 seconds.

Next, press the 'Info' button on the DIC until the remaining oil life is displayed on the screen. This may be indicated by a picture of a car with a 'invasione' symbol. While the remaining oil life is displayed on the screen, press and hold the 'checkmark' button until the oil life resets to 100%.

Finally, turn the ignition off. The oil reset is now complete.

It is important to note that the oil life display must be reset after each oil change. It will not reset itself. Do not reset the oil life display accidentally unless the oil has just been changed.

Resetting the oil change light with the gas pedal

To reset the oil change light with the gas pedal on a 2008 Chevrolet Express van, follow these steps:

First, turn the key forward to the "on" position without starting the car. You want to have accessory mode on without cranking up the engine.

Then, fully press and slowly release the accelerator (gas) pedal three times within five seconds. You should notice that the oil light will start flashing. Once it starts flashing, it will flash two or three times before the light goes off.

Now, start the car and check the dashboard. The oil light should be gone.

If the above method does not work, there is another way to reset the oil life using the DIC button on the left side of the instrument cluster or the screen. Turn the key to the "on" position without starting the engine. Press the "Info" or "Car Info" button on the DIC until the remaining oil life is displayed on the screen. While the remaining oil life is displayed, press and hold the checkmark button until the oil life resets to 100%. Finally, turn off the ignition, and the oil reset is now complete.

It is important to note that the oil life display must be reset after each oil change. Do not reset the oil life display accidentally unless the oil has just been changed.

Finding the fuel filter

To find the fuel filter on a 2008 Chevy Express van, you should look in the fuel line, either near the fuel tank or close to the engine.

The fuel filter is usually found where the fuel line connects to the side of the fuel tank. This is in line with the gasoline line, and you can remove and replace it without needing to drain and drop the fuel tank.

If your fuel system is not getting enough pressure, this could be a sign that your fuel filter is clogged with debris. This will reduce the amount of fuel that goes through the lines, which can cause the motor to run poorly or stall while driving.

Frequently asked questions