Replacing The Fuel Pump In Your 2002 Honda Accord

Replacing the fuel pump on a 2002 Honda Accord is a moderately complicated job that can be done at home or by taking the car to a dealership’s service department. The fuel pump is located inside the fuel tank and can be accessed by removing the trunk floor and taking out an access panel. The process involves siphoning out the gas tank, disconnecting the fuel lines, removing the fuel pump, installing the new pump, and reconnecting the fuel lines. This process is more complicated for fourth and fifth-generation Honda Accords, as it requires draining the gas, dropping the tank, and disconnecting all the fuel lines to access the pump.

Siphon out the gas tank

To siphon the gas out of your 2002 Honda Accord, you will first need to remove the trunk floor to access the fuel pump. You can then use a siphoning hose to drain the gas tank.

• Park your car on a level surface and engage the parking brake.
• Remove the trunk floor by unscrewing the bolts or fasteners holding it in place. You may need to refer to your car's repair manual for the exact procedure, as it may vary slightly between models.
• Locate the fuel pump access panel. This is usually underneath the rear seat or trunk floor.
• Once you have located the access panel, remove it to expose the fuel pump.
• Place a suitable container to catch the gasoline below the fuel pump.
• Obtain a siphoning hose or tube. You can purchase these from most auto parts stores or hardware stores. Ensure the hose is designed for fuel and is long enough to reach from the fuel pump to your container.
• Place one end of the hose into the fuel tank through the access panel and secure it so it won't fall in.
• Place the other end of the hose into your container. Ensure this end is lower than the end in the fuel tank to allow the gasoline to flow via gravity.
• Start siphoning by sucking on the end of the hose in the container. Be careful not to ingest any gasoline. You can also use a manual or electric siphon pump if you prefer.
• Allow the gasoline to flow into the container until the tank is empty.
• Once the tank is empty, carefully remove the hose and seal the access panel.
• Reinstall the trunk floor and securely fasten it in place.

Note: Always exercise extreme caution when handling gasoline. Ensure the area is well-ventilated, avoid open flames or sparks, and wear appropriate safety gear, including eye protection and gloves.

Raise and secure the car

To replace the fuel pump on a 2002 Honda Accord, you will need to raise and secure the car safely. Here is a step-by-step guide to doing this:

Firstly, choose the right equipment for your vehicle. You will need a hydraulic car jack and jack stands that are appropriate for your car's weight. Do not use the emergency jack supplied with your vehicle, as it is only for short-term use.

Next, identify the correct jack points as specified in your owner's manual. These points are engineered to support the car's weight during a lift, so it is crucial to use these specific areas to avoid damage to the vehicle or unstable lifting. Common jack points are under the vehicle's subframe or along the pinch welds.

Before lifting, ensure your car is on a firm, level surface, preferably concrete or asphalt. Engage the parking brake and place wheel chocks on the opposite side of the vehicle being lifted to prevent rolling. If your car has a manual transmission, put it in gear, or put it in park if it is an automatic.

Now you can start lifting the car. Position the hydraulic jack at the correct jack point and pump the jack handle steadily to raise the car to the desired height. Stop once you have enough clearance to access the fuel pump.

Do not rely solely on the hydraulic jack to support the vehicle. Place jack stands beneath the vehicle, adjacent to the jack points, to secure the car's weight. This step is critical to mitigate the risk of the car falling unexpectedly.

Once the car is raised and secured, gently shake the vehicle to ensure stability before proceeding with any repairs.

Remember to always put safety first when working on your car. Never work underneath a vehicle that is only supported by a jack. Always use jack stands and wheel chocks, and work on a level surface to avoid an unstable lift.

Disconnect the fuel-sending unit

To disconnect the fuel-sending unit of a 2002 Honda Accord, follow these steps:

Firstly, you need to locate the fuel-sending unit. This can be found by opening the access hatch inside the trunk. You will need to remove the trunk floor to reveal the access hatch. Once you have located the access hatch, open it.

Now, you can disconnect the fuel-sending unit. It is important to carry out this process safely, so ensure you are working in a well-ventilated area, and the engine is turned off to avoid any risk of ignition. You may also want to wear gloves and eye protection for this step.

The next step is to disconnect the fuel lines. There are four fuel lines that need to be disconnected, and these are all located behind the left rear wheel. Start by removing the rear left wheel, and then begin to disconnect the fuel lines. There are two hard lines, a high-pressure line, a brass line that connects to the tank, and a large line for fuel input.

Once all the fuel lines are disconnected, you have successfully disconnected the fuel-sending unit. You can now proceed to remove the tank straps and lower the tank to access the fuel pump.

Disconnect the fuel lines

To disconnect the fuel lines of your 2002 Honda Accord, follow these steps:

First, remove the rear left wheel. Once the wheel is off, you can begin to disconnect the fuel lines. There are four fuel lines that need to be disconnected, all of which are located behind the left rear wheel.

The first two fuel lines to disconnect are the hard lines. After these, you will need to disconnect the high-pressure line. Then, disconnect the brass line that connects directly to the tank. Finally, disconnect the large line for fuel input.

It is important to note that you will need to use a jack to raise and secure the car before attempting to disconnect the fuel lines. Additionally, make sure to place jack stands under the car for added security.

Remove the tank straps

To remove the tank straps on a 2002 Honda Accord, you will need to place a hydraulic jack with a long piece of wood under the tank. The tank straps are held in place using 14mm bolts, so you will need to loosen these with a socket wrench.

Before you begin, you will need to siphon the gas out of the tank. You can do this by taking a tube and inserting it into the tank through the gas cap. Create a vacuum by blowing into the tank through the tube and pour the gasoline into a safe container. Drain out as much gas as possible.

Next, you will need to raise and secure the car. Use a jack on one of the car's safety points and raise it. Position jack stands under the car to secure it in the air.

Now you can begin to disconnect the fuel lines. There are four fuel lines that need to be disconnected, and they are all located behind the left rear wheel. Remove the rear left wheel and begin disconnecting the fuel lines. There are two hard lines, a high-pressure line, one brass line that connects directly to the tank, and a large line for fuel input.

The exhaust heat shield may need to be removed to access one of the 14mm strap bolts. Once the straps are loose, slowly lower the tank to relieve the pressure from the jack.

Frequently asked questions