Replacing Fuel Line On A Weedeater: A Step-By-Step Guide

If the fuel line on your weed eater has cracked or split, you can replace it yourself. This is a guide on how to replace the fuel line on a weed eater. First, disconnect the spark plug wire and remove the fuel cap. Drain the fuel from the tank into an approved container. Remove the fuel filter and then disconnect the fuel lines from the carburetor. Pull the fuel lines out of the tank and tip the trimmer to remove any remaining pieces. Feed the new fuel lines into the tank, cutting the ends at an angle to make this easier. Reattach the fuel filter and reconnect the fuel lines to the carburetor. Finally, reconnect the spark plug wire and test the weed eater.

Disconnect the spark plug wire

Before you begin working on your weed eater, ensure that it is turned off and disconnected from any power source. This is a vital safety precaution as it prevents accidental starts. You should also allow the engine to cool down completely before proceeding to avoid the risk of burns. It is also recommended that you put on safety gear, such as gloves and goggles, to protect your hands and eyes from dirt and debris.

Now, locate the spark plug. It is typically found on the engine block of your weed eater and will have a thick wire (the spark plug wire) connected to its terminal. Use a clean cloth or rag to wipe away any dirt or debris around the spark plug to prevent contaminants from falling into the combustion chamber when the plug is removed.

The next step is to disconnect the spark plug wire. Pull the spark plug wire straight off the spark plug. This step will allow you to access the fuel tank and proceed with the rest of the fuel line replacement process.

Remember to exercise caution throughout the process, especially when working with combustible materials and electrical components. Always refer to the manufacturer's instructions or seek professional assistance if you are unsure about any steps or procedures.

Remove the fuel filter

To remove the fuel filter from your weed eater, you'll first need to locate it. The fuel filter is inside the gas tank—it's a white cylinder attached to the end of the small fuel line.

Once you've found it, you can use a pair of needle-nosed pliers or a straightened wire clothing hanger with a hook formed on the end to fish the filter out of the tank. Be careful not to drop any debris into the tank while you're doing this.

Now that you have a hold of the fuel filter, simply pull it off the end of the fuel line. You may need to wiggle it a little to get it off, but it should come away without too much force.

Set the old fuel filter aside and get ready to install the new one. It's important to note that you should always wear nitrile gloves if you're concerned about your skin coming into contact with fuel. It's also a good idea to work in a well-ventilated area, away from any ignition sources.

Disconnect the lines from the carburetor

Disconnecting the fuel lines from the carburetor is a crucial step in replacing the fuel line on a weed eater. Here is a detailed, step-by-step guide to help you through the process:

Before you begin, it is important to work in a well-ventilated area, away from any ignition sources. Ensure you are wearing the appropriate safety gear, including gloves and safety goggles.

First, remove the spark plug wire from the spark plug. Set it aside, ensuring it does not come into contact with the spark plug. Next, drain any remaining fuel from the fuel tank into an approved container. Old fuel is considered hazardous waste, so be sure to dispose of it properly.

Now, you will need to disconnect the fuel lines from the carburetor. Start by making a diagram or taking a picture of how the fuel lines are configured between the fuel tank and the carburetor. This will be useful for reference when reconnecting the new fuel lines.

Using a pair of needle-nose pliers or hemostat forceps, carefully remove the fuel lines from the carburetor. If the fuel lines are difficult to grasp, you may need to use a straightened wire clothing hanger to reach them. Be cautious not to spill any fuel during this step, and wipe away any spills with a cloth.

Once the fuel lines are disconnected from the carburetor, pull the old lines out of the fuel tank. Again, needle-nose pliers or hemostat forceps can help with this step. If the lines are stubborn, you may need to cut them flush with the tank and use a small screwdriver to push the remnants into the tank. Tip the weed eater and shake it to ensure all pieces of the old fuel line are removed.

After disconnecting and removing the old fuel lines, you can begin preparing the new fuel lines for installation. It is important to follow the specific instructions for your weed eater model, as the configuration of the fuel lines may vary. Refer to your diagram or picture to ensure you understand how the lines were previously connected.

Now, you are ready to install the new fuel lines and reconnect them to the carburetor. Follow the steps provided in your weed eater's manual or seek further guidance to complete the installation process.

Pull the fuel lines out of the tank

Pulling the fuel lines out of the tank is a crucial step in replacing the fuel line on your weed eater. Here's a detailed guide on how to do it:

Before you begin, ensure you have the necessary tools, such as needle-nose pliers or hemostat forceps, and that you are working in a well-ventilated area. It is also recommended to wear nitrile gloves to protect your skin from fuel contact.

Now, let's get started:

• Disconnect the spark plug wire from the spark plug. This is an important safety precaution to prevent any accidental ignition during the process.
• Drain any remaining fuel from the tank into an approved container. Old fuel is considered hazardous waste, so be sure to dispose of it properly.
• Remove the fuel lines from the carburetor using your needle-nose pliers or hemostat forceps. This step may require some force, but be careful not to damage the surrounding components.
• Grasp the old fuel line inside the tank firmly with your pliers or forceps. Pull the line out of the tank through the filler opening. If the fuel line breaks during this process, don't worry. Simply tip the weed eater and shake it gently to remove any remaining pieces from the tank.
• Once the fuel line is completely removed, locate the fuel filter and plastic connector (if present) and set them aside. These parts may be reused if they are in good condition.
• At this point, you should have successfully removed the old fuel line from the tank. Take a moment to inspect the tank for any debris or remaining fuel. Ensure it is clean and dry before installing the new fuel line.
• If your weed eater model has two fuel lines of different diameters, identify the smaller line, which is usually the suction line. It should have a filter attached to its end.
• Install the small fuel line by cutting its end at an angle. This angled cut will make it easier to thread the line into the tank.
• Push the angled end of the small line into the corresponding hole in the tank. Use your pliers or forceps to grab the line inside the tank and pull it through the filler opening. You should pull out enough line to work with, approximately 4 inches or so.
• Cut the end of the small line square and attach the fuel filter. Ensure the filter is securely attached to the line.
• Now, you can feed the small line back into the tank, allowing the filter to lay flat on the bottom. The line should be long enough so that the filter rests on the bottom of the tank.

By following these steps, you will have successfully pulled out the old fuel line and installed the new small fuel line into the tank of your weed eater. Remember to refer to a repair guide or manual for your specific weed eater model, as some variations may exist between different brands and models.

Feed the new fuel lines into the tank

Now that you have removed the old fuel lines and are ready to install the new ones, it's time to feed the new fuel lines into the tank. This process will involve several steps and tools, including needle-nose pliers, scissors, and hemostat forceps. Here is a detailed guide to help you through the process:

Firstly, you will need to cut the ends of the new fuel lines at an angle. This step will make it easier to thread the lines into the tank. Use scissors to cut the ends of both the small and large fuel lines. The new lines are slightly bigger than the holes in the tank, creating a seal against the tank.

Next, you will need to force the cut ends of the fuel lines into the proper holes in the tank. The smaller line is the suction line and should have a filter on its end. Push this line into the tank, ensuring that the filter lays flat on the bottom of the tank. The larger line should be pushed about an inch into the tank. If necessary, use needle-nose pliers to grip the lines and force them into the correct holes.

If the lines are tight and difficult to push through, apply a small amount of oil to the outside of the lines. This will help them slide through more easily.

Once the lines are in place, use hemostat forceps or needle-nose pliers to grab the lines inside the tank and pull them through the fuel tank filler opening. Pull out about 4 inches of the line. If the line is difficult to pull through, you can spray a little WD-40 to help it slide more easily.

Now, cut the end of the small line square and attach the fuel filter. Push the filter into the tank, ensuring it rests on the bottom. The small line is now ready to be attached to the carburetor.

Finally, cut the larger line square as well, and pull it out of the tank. If your model has a connector, push it onto the fuel line, and then pull the line out until the connector is against the hole in the tank. Once the line is in position, it is ready to be connected to the carburetor.

By following these steps, you will have successfully fed the new fuel lines into the tank, and your weed eater will be one step closer to being fully functional again!

Frequently asked questions