Replacing Fuel Hose On A Ranch King Snowblower: Step-By-Step Guide

If you're experiencing issues with your Ranch King snowblower, it could be time to replace the fuel hose. The fuel hose carries fuel from the gas tank to the engine, so a damaged hose can prevent fuel from reaching the carburetor and starting the engine. In this guide, we'll walk you through the process of replacing the fuel hose on your snowblower, ensuring your machine is ready for the winter season ahead.

Drain the fuel tank and disconnect the spark plug wire

Before you begin to replace the fuel hose on your Ranch King snowblower, it is important to take the necessary safety precautions. Position the snowblower in a well-ventilated area and drain the fuel from the tank. If you are unable to drain the fuel, you can run the snowblower until the tank is empty.

Once the tank is empty, you can begin to disconnect the spark plug wire. Locate the spark plug and pull the wire up and off the plug. It is important to be gentle during this process to avoid damaging the wire or the plug. With the spark plug disconnected, you can now safely proceed with replacing the fuel hose on your Ranch King snowblower.

After completing this step, you will need to remove the electric starter switch. First, remove the mounting screws that secure the switch to the bracket. Once the screws are removed, pull the starter switch off the bracket and let it hang by the electrical cord. Now you can move on to removing the engine shroud, which will give you access to the fuel line and other components.

The engine shroud can be removed by first pulling off the choke and throttle knobs. Next, remove the acorn nuts that secure the carburetor to the engine. Then, remove the muffler shroud mounting screws. Work the engine shroud off the carburetor mounting studs, being careful not to disconnect the primer hose and breather hose. With these steps completed, you can now access the fuel line and proceed with the replacement process.

Remove the electric starter switch

To remove the electric starter switch on a snowblower, you will need to disconnect the spark plug wire. Pull the spark plug wire straight up and off the plug. Next, remove the mounting screws that hold the switch box to the engine. There should be two screws to remove. Once these are removed, pull the switch box away from the engine, allowing it to hang by the power cord attached to the starter motor.

Now, remove the two starter motor mounting screws and pull the starter motor off the engine. The electric starter switch should now be fully removed.

Before beginning any repairs or maintenance, ensure the engine is not locked up. If it is locked, the electric starter will not spin the engine.

Remove the engine shroud

To remove the engine shroud, you will need to first pull off the choke and throttle knobs. You should then remove the acorn nuts that secure the carburetor to the engine. Next, remove the muffler shroud mounting screws. Finally, work the engine shroud off the carburetor mounting studs, leaving the primer hose and breather hose connected.

The engine shroud is located under the bottom lip of the muffler shroud, so you will need to remove the muffler shroud before reinstalling the engine shroud. You can remove the engine shroud without taking off the muffler shroud, but the muffler shroud must be removed for reassembly.

To remove the muffler shroud, first pull off the muffler shroud mounting bolts. Then, release the wire control cables from the retainer clip and pull off the muffler shroud.

When you are ready to reinstall the engine shroud, align the choke knob shaft and the two carburetor mounting posts with the openings on the engine shroud. Work the engine shroud onto the engine, ensuring that the breather hose passes through the opening and lines up with the rocker cover breather hose fitting. Secure the breather hose with the clamp.

Remove the fuel line

To remove the fuel line, you will need to release the fuel line clamp and pull the fuel line off the fuel filter. You will need to repeat this process to release the other end of the fuel line from the carburetor and remove it. Ensure you are working in a well-ventilated area.

To begin, locate the fuel line clamp and use an appropriate tool to loosen it. Once the clamp is loosened, carefully pull the fuel line away from the fuel filter. It may take some force to remove it, but be gentle to avoid damaging any nearby components.

Next, move to the other end of the fuel line, which is connected to the carburetor. Again, release the fuel line clamp and gently pull the fuel line free. Take care not to spill any fuel during this process.

Now that you have removed both ends of the fuel line, you can lift it out and set it aside. Be sure to place it somewhere safe and clean, as you will need to dispose of it properly later.

With the old fuel line removed, you can now prepare to install the new one. It is important to follow the correct procedures and take safety precautions when working with fuel lines to avoid any leaks or damage to your snowblower.

Install the new fuel line

To install the new fuel line, first, connect the new fuel line to the tank and secure it with the fuel line clamp. Then, repeat the process to connect the other end of the new fuel line to the carburetor. Ensure that the fuel line is securely attached at both ends before proceeding.

It is important to note that the fuel line should be replaced with a manufacturer-approved replacement part to ensure compatibility and safety. The fuel line carries fuel from the gas tank to the engine, so it is important to make sure that it is properly installed and secure to prevent fuel leaks.

Additionally, when working with fuel lines and gasoline, it is crucial to take the necessary safety precautions. Work in a well-ventilated area and avoid open flames or sparks that could ignite the gasoline. Always refer to the owner's manual for specific instructions and safety guidelines.

Frequently asked questions