Sylvie Willis
If you need to drain the fuel tank of your 2009 Yamaha FZ6, there are several methods you can use. Some people suggest using a siphon pump or a rubber hose to remove the fuel, while others recommend removing the fuel tank and then draining it by turning it upside down or shaking it over a bucket. If you want to avoid spillage, you can try removing the fuel pump or fuel filter, or simply riding the bike until the tank is empty. It's important to note that old fuel can damage your engine, so be cautious if your bike has been sitting in the garage for a long time.
How to drain the fuel tank of a 2009 Yamaha FZ6
| Characteristics | Values |
|---|---|
| Fuel tank removal | Remove the seat, then the two bolts at the front of the tank by the headstock. Flip the tank up and place it in an old oil container. |
| Fuel removal | Pull out the breather pipes on the right-hand side. Disconnect the electrical harness for the fuel pump. Remove the fuel pump or use a siphon pump to drain the fuel. |
| Fuel tank reinstallation | Reinstall the breather hoses to make it easier to put the tank back in place. |
| Fuel tank leakage | Check for any signs of rust or damage to the fuel hose, which could cause leakage. |
Explore related products
What You'll Learn
Siphoning the tank
To siphon the fuel tank of your 2009 Yamaha FZ6, you can follow these steps:
Firstly, take your seat off. Then, remove the two bolts at the front of the tank by the headstock. If your bike has side panels, you will need to remove those as well. Once the bolts are removed, flip the tank up and prop it up securely, using an old oil container or another suitable object.
Next, carefully pull out the two breather pipes on the right-hand side of the bike. These pipes connect to the tank, so be cautious not to split or break them. It is recommended to keep them attached to the tank once removed. After that, disconnect the electrical harness for the fuel pump by pulling off the two connectors. Ensure you remember which connector goes where to facilitate reassembly.
Now, you can remove the fuel line. There is a little clip that holds it in place, so simply clip it off. Then, you will see the fuel line with two "buttons" on the side. Pinch these together, and you can pull the pipe off. Again, be careful not to break the connector.
At this point, you can begin the siphoning process. Insert a siphon hose as far down towards the seat as possible. You can use a self-priming siphon hose/pump, which can be found at hardware stores like Lowe's or Home Depot for a low price. Move the pump back and forth rapidly to empty the tank quickly and efficiently.
It is important to note that some fuel may remain at the bottom of the tank after siphoning. If you need to remove all fuel, you can try removing the fuel pump and shaking the tank over a wide bucket. Alternatively, you can flush the tank with alcohol to dry up any remaining gasoline.
Creating an Extended Fuel Tank for Your Honda 2000
You may want to see also
Explore related products
Removing the fuel pump
Firstly, it is important to prepare the motorcycle for the procedure. Place the motorcycle on a stable and level surface, and ensure that the engine is turned off and cooled down. Remove the seat to access the fuel tank and its components.
The next step is to locate and remove the fuel pump. The fuel pump is typically located at the bottom of the fuel tank and is responsible for delivering fuel from the tank to the engine. Remove the bolts securing the fuel pump to the tank, being careful not to drop them into the tank. Once the bolts are removed, carefully lift the fuel pump out of the tank, taking note of any attached hoses or connectors.
Before proceeding further, it is crucial to address any remaining fuel in the tank. Use a siphon or a hand pump to drain the fuel from the tank. This step is essential for safety and to prevent fuel spillage during the rest of the process. Ensure that you collect the drained fuel in an appropriate container.
Now, with the fuel safely drained, you can focus on detaching the fuel pump's connections. Carefully disconnect the electrical harness for the fuel pump by pulling off the connectors. It is important to note that there may be multiple connectors, so take care to remember which connector goes to which component. Additionally, look for any breather hoses attached to the fuel pump and carefully remove them, ensuring that you do not split or damage the hoses.
Finally, you will need to detach the fuel line from the fuel pump. Locate the clip that holds the fuel line in place and carefully remove it. The fuel line may have "buttons" or other mechanisms on the side that need to be pinched together to release the line. Be cautious not to break any connectors during this process. With the fuel line detached, you have successfully removed the fuel pump from your 2009 Yamaha FZ6.
Remember to handle fuel with care and ensure proper ventilation during the process. If you are unsure about any steps or encounter complications, it is always best to consult a professional or a mechanic for assistance.
Draining a Lawn Mower Fuel Tank: Step-by-Step Guide
You may want to see also
Explore related products
Using a hand pump
To drain the fuel tank of a 2009 Yamaha FZ6 using a hand pump, follow these steps:
Firstly, it is important to note that the service manual for the FZ6 indicates that the fuel needs to be pumped out before removing the fuel tank. This is to avoid potential spillage and leakage when the tank is removed. While some people have removed the tank with fuel still in it without experiencing major issues, it is generally recommended to drain the tank beforehand to be safe.
Now, to use a hand pump to drain the fuel, you can start by purchasing an inexpensive siphon pump from stores like Home Depot, Lowe's, or Autozone. These pumps are typically priced between $1.99 and $6.
Once you have the pump, you can insert the pump side into the fuel tank. If you want to avoid removing the tank, you can simply stick the pump into the opening and let it suck out the gas. Alternatively, you can tilt the tank back and use the hand pump to suck out the fuel.
If you need to completely empty the tank, you may need to flush it with alcohol to dry up any remaining gasoline. Additionally, make sure to leave the fuel cap open overnight to allow any remaining fuel vapour to evaporate.
Finally, remember to always exercise caution when handling fuel and ensure you are in a well-ventilated area to avoid inhaling fumes.
Destroying Fuel Tanks in Storm Eagles: A Step-by-Step Guide
You may want to see also
Explore related products
Flushing with alcohol
If you need to get your Yamaha FZ6 motorcycle fuel tank bone dry, flushing it with alcohol is the way to go. Here's a step-by-step guide on how to do it:
First, you'll need to get your hands on some denatured alcohol, also known as methylated spirits. This is a type of alcohol that is not suitable for human consumption and is often used for cleaning and solvent purposes. You should be able to find it at your local hardware store or auto supply store.
Next, locate the fuel tank on your 2009 Yamaha FZ6. The Yamaha FZ6 has a fuel pump, and the service manual indicates that the fuel needs to be pumped out before removing the tank. You can do this by using a hand pump or a siphon pump, which you can buy at most hardware stores. Tilt the tank back and use the pump to suck out as much of the fuel as possible.
Once you've removed the majority of the fuel, it's time to start the flushing process. Remove the fuel pump from the tank, if possible. If you're unable to remove the fuel pump, that's okay—you can still flush the tank with alcohol. Pour a generous amount of denatured alcohol into the tank, ensuring it covers the bottom of the tank completely.
Now, you'll want to agitate the alcohol to help it mix with any remaining gasoline. You can do this by tilting and shaking the tank gently. The alcohol will help dissolve and flush away any gasoline residue, ensuring your tank is truly empty.
Finally, drain the alcohol-gasoline mixture from the tank. You may need to repeat the process a few times, using fresh alcohol each time, until the tank is completely dry. Remember to dispose of the alcohol-gasoline mixture responsibly, following local guidelines for hazardous waste disposal.
Flushing your Yamaha FZ6's fuel tank with alcohol is a surefire way to ensure it's completely empty and dry. This method is especially useful if you need to ship your bike or store it for an extended period. As always, exercise caution when handling flammable liquids, and make sure you have adequate ventilation when working with them.
Draining Freelander 2 Fuel Tank: Step-by-Step Guide
You may want to see also
Explore related products
Removing the tank
To remove the tank of your 2009 Yamaha FZ6, you will first need to remove your seat. Then, remove the two bolts at the front of the tank by the headstock. If your bike has side panels, you will need to remove them first. Once the bolts are removed, flip the tank up and prop it up on something like an old oil container or a box.
Next, you will need to remove the two breather pipes on the right-hand side of the bike. Be careful when pulling them through, so you do not split or break them. You can then keep them attached to the tank. Now, disconnect the electrical harness for the fuel pump by pulling off the two connectors. Remember which connector is for which. Once that is done, remove the fuel line by clipping off the little clip that holds it on. There will be two "buttons" on the side of the fuel line; pinch these together, and you can pull the pipe off. Be careful not to break the connector.
If you want to drain the fuel, you can either remove the filler cap or the fuel pump. Removing the fuel pump requires a bit more finesse, and you will need to be careful not to break the release tab. If you are removing the fuel pump, you will need to hold the tank over a wide bucket and shake it to get the remaining fuel out. Alternatively, you can use a siphon to drain the fuel. If you are not removing the fuel pump, make sure you do not tip the tank upside down, or it will leak out of the flood line.
Draining the Duramax Fuel Tank: Step-by-Step Guide
You may want to see also
