Replacing The Fuel Pump In A 2005 Honda Accord: Step-By-Step Guide

If your 2005 Honda Accord is acting up, a fuel pump replacement might be in order. Fuel pumps are expected to wear out over time, especially in vehicles with higher mileage. While diagnosing a fuel pump issue can be relatively easy, replacing it is a bit more involved. This is especially true for fourth and fifth-generation Honda Accord owners, who will have to drain the gas, drop the tank, and disconnect all the fuel lines to access the pump. However, with the right tools and know-how, you can save yourself a few hundred dollars in labour costs.

Siphoning out the gas tank

To begin siphoning, you will need a tube that is long enough to reach the bottom of the gas tank. Insert one end of the tube into the tank through the gas cap. Before proceeding, ensure that the tube is suitable for this task and that you are wearing appropriate safety gear, including gloves and eye protection.

Once the tube is in place, create a vacuum by blowing into the tube. This will help start the flow of gasoline. You can then pour the gasoline into a safe container. It is important to use a container that is specifically designed for storing flammable liquids and to keep it away from any sources of ignition.

Continue siphoning until you have drained out as much gas as possible. If you have access to a vacuum pump, you can use it instead of the tube to avoid the risk of accidentally sipping gasoline. This will make the process safer and potentially faster.

After you have finished siphoning, make sure to properly seal and store the container with the drained gasoline in a well-ventilated area, away from any open flames or other sources of ignition.

Now that the gas tank is empty, you can proceed to the next steps of raising and securing the car, disconnecting the fuel-sending unit, and so on. Remember to always refer to a trusted repair manual or seek professional assistance if you are unsure about any part of the process.

Raising and securing the car

To raise and secure your 2005 Honda Accord, you'll need to use a car jack and jack stands. Place the jack under one of the car's safety points and raise it until you have enough space to work underneath.

Once the car is raised to the desired height, you'll need to position the jack stands under the vehicle to secure it in the air. Consult your Honda Accord manual or a repair guide to locate the exact jacking points and the correct placement of the jack stands. It is crucial to use the designated safety points to avoid any damage to the vehicle or accidents.

After positioning the jack stands, carefully lower the car onto them, ensuring it is stable and secure. You can now proceed with the next steps, which involve working underneath the car. Remember always to exercise extreme caution when working with a raised vehicle. Ensure the car is securely supported, and never work alone if possible.

When you have finished working underneath the car, use the jack to lift the vehicle off the jack stands. Once the car is stable on the jack, you can remove the jack stands. Finally, carefully lower the vehicle to the ground by slowly turning the jack handle in the opposite direction. Ensure the car is securely resting on the ground before proceeding with any further repairs or maintenance.

Disconnecting the fuel-sending unit

To disconnect the fuel-sending unit of your 2005 Honda Accord, you will need to locate the access hatch inside the trunk. This is found underneath the trunk, behind an access panel. Open this hatch to reveal the fuel-sending unit.

The fuel-sending unit is what you need to disconnect to begin the process of replacing the fuel pump. This is Step 3 of the fuel pump replacement process, which also includes siphoning out the gas tank, raising and securing the car, and disconnecting the fuel lines.

Once you have located the fuel-sending unit, you can begin the process of disconnecting it. This may involve removing any screws or fasteners that are holding it in place. Be sure to have a container ready to catch any fuel that may spill during this process, as you will need to disconnect the unit from the fuel lines.

After you have successfully disconnected the fuel-sending unit, you can move on to Step 4, which is to begin disconnecting the fuel lines. There are four fuel lines in total that will need to be disconnected, and these are located behind the left rear wheel.

Disconnecting the fuel lines

To disconnect the fuel lines of a 2005 Honda Accord, you must first raise and secure the car using a jack. Once the car is safely in the air, you can begin the process of disconnecting the fuel lines.

There are four fuel lines that need to be disconnected, and they are all located behind the left rear wheel. To access them, you must first remove the rear left wheel. Once the wheel is removed, you will see two hard lines, a high-pressure line, and a brass line that connects directly to the tank. There is also a large line for fuel input.

Using the appropriate tools, carefully disconnect each of the four fuel lines. Be sure to have a container ready to catch any fuel that may spill during this process. It is also recommended to wear safety gloves and goggles to protect your hands and eyes.

Once all the fuel lines have been disconnected, you can move on to the next step, which is removing the tank straps.

Removing the fuel pump

To remove the fuel pump from a 2005 Honda Accord, you'll need to first siphon the gas from the tank. Take a tube and insert it into the tank through the gas cap. Blow into the tank through the tube to create a vacuum and pour the gasoline into a safe container. Drain out as much gas as possible.

Next, use a jack to raise and secure the car. Place jack stands under the car to secure it in the air.

Now, you can begin disconnecting components. Disconnect the fuel-sending unit, which is found underneath the access hatch located inside the trunk. Then, remove the rear left wheel and disconnect the four fuel lines located behind it. There are two hard lines, a high-pressure line, a brass line that connects directly to the tank, and a large line for fuel input.

Remove the tank straps with a 14mm bolt. Place a hydraulic jack with a long piece of wood under the tank, loosen the straps, and remove them. Once the straps are off, slowly lower the tank to relieve the pressure from the jack.

Finally, you can remove the fuel pump. First, disconnect the clip on top of the fuel pump. Then, use a 10mm socket to remove the nuts that secure the fuel pump to the tank. Once the nuts are off, pull the unit out of the tank and remove the pump from its bracket.

Please note that these instructions are for general information purposes only. For specific details on removing the fuel pump from your 2005 Honda Accord, it is recommended to refer to the vehicle's repair manual or seek advice from a qualified mechanic.

Frequently asked questions