Replacing The Fuel Tank In A 1998 Toyota Corolla Diy Guide

If you're looking to replace the fuel tank in your 1998 Toyota Corolla, you'll first need to jack up the back end of the car to create enough clearance to remove the tank. Next, you'll need to evacuate the fuel from the tank by removing the plug on the bottom with a socket wrench. There are also straps holding the fuel tank in place that need to be loosened and removed before you can take the tank out. You'll also need to disconnect the fuel pump wires by unplugging them. Be sure to take the necessary safety precautions when working underneath the vehicle, such as chocking the wheels and setting the parking brake. Additionally, you may need to remove a shield that is held in place by bolts if your Corolla model has one.

Jack up the back end of the car

Jacking up the back end of your 1998 Toyota Corolla is a relatively straightforward process, but it's important to take safety precautions to avoid injury or damage to your vehicle. Here's a detailed guide on how to do it:

Park on a Stable Surface:

First, make sure you park your car on a hard, flat surface, such as a concrete driveway or a garage floor. Avoid jacking up your car on unstable or soft ground, and stay away from potential hazards or moving vehicles.

Use Wheel Chocks:

Place wheel chocks, or wedges, in front of each wheel at the front of the car. These wedges can be made of wood or rubber, and they help to keep your tires secure while the back end is lifted. If you don't have chocks, you can use bricks or other sturdy objects as substitutes.

Put the Car in "Park":

Before proceeding, make sure your car is in "Park." If your Corolla has a manual transmission, keep it in the lowest gear. This step is crucial for safety, as it prevents the car from rolling.

Locate the Rear Jack Point:

Refer to your owner's manual to locate the jack points on your 1998 Toyota Corolla. There should be a jack point on each side of the vehicle, behind the front wheels, and in front of the rear wheels, close to the rocker panels. These jack points will be flat metal areas and may have notches that match the shape of the top of the jack.

Position the Jack:

Slide the jack right below the rear jack point on either side of the car. Ensure that the jack is properly positioned with the correct side facing up. Refer to the jack's user manual for specific instructions on its positioning.

Raise the Jack:

Start raising the jack until it touches the underside of the car. Depending on the type of jack you have, you may need to turn or pump a lever to raise it. As you raise the jack, make fine adjustments to ensure it lines up properly with the jack point. Continue jacking until the back end of the car starts to lift off the ground.

Use Jack Stands:

If you plan to work underneath the car, it is essential to use jack stands or wheel cribs for added safety. These supports are affordable and readily available at auto stores. Place the jack stands under the jack points near the rear wheels and slowly lower the jack until the stands are securely supporting the car.

Lower the Vehicle:

Once you have completed your repairs or maintenance, gradually lower the car back to the ground and remove the jack stands and then the jack. Remember to remove the wheel chocks as well.

By following these steps, you can safely jack up the back end of your 1998 Toyota Corolla and perform the necessary work without putting yourself or your vehicle at risk.

Evacuate the fuel from the tank

To evacuate the fuel from the tank of a 1998 Toyota Corolla, you will need to jack up the back end of the car to allow enough clearance to remove the fuel tank. Once the car is jacked up, locate the plug on the bottom of the fuel tank and remove it with a half-inch socket wrench. This will allow the fuel to drain out of the tank.

It is important to work with extreme caution when dealing with fuel. The battery should be disconnected, and proper precautions should be taken against fire hazards.

After evacuating the fuel, the next step is to locate and loosen the straps holding the fuel tank in place. There are two straps running from front to back, each held in place by two bolts on either side. Loosen these bolts with a socket wrench, but do not remove them yet. Place a second jack under the fuel tank and elevate it until it touches the bottom of the tank. Now you can remove the straps, and the tank should be resting on the jack.

Loosen the straps holding the tank

To loosen the straps holding the tank of your 1998 Toyota Corolla, first jack up the back end of the car to create clearance for room to remove the fuel tank. Next, evacuate the fuel from the gas tank by removing the plug on the bottom of the tank with a half-inch socket wrench.

Now, locate the straps holding the fuel tank. There will be two straps running from front to back. Loosen the first strap with a socket wrench. There are two bolts for each side of the strap, tightened into the vehicle cross-members. Do not remove this strap yet. Instead, move on to the second strap and loosen it in the same way. Do not remove the second strap yet, either.

Place a second jack under the fuel tank and elevate it until it touches the bottom of the tank. Now, you can remove the straps. The tank should now be resting on the jack.

Place a jack under the tank and elevate

Once you've jacked up the back end of the car and evacuated the fuel from the gas tank, you'll need to locate the straps holding the fuel tank in place. There are two straps running from front to back, each with two bolts on either side. Loosen the bolts on both straps with a socket wrench, but don't remove them yet.

Now, place a second jack under the fuel tank. Slowly elevate the jack until it makes contact with the bottom of the tank. Be careful not to place too much pressure on the tank, as this could cause damage. Once the jack is in position, you can remove the straps completely. The tank should now be resting securely on the jack.

At this point, you can slowly lower the jack until the fuel pump wires are accessible. You should then be able to remove these wires by unplugging them from the top of the tank. With the wires disconnected, you can now remove the tank from underneath the vehicle. Remember to lower the car from the first jack before attempting this step.

Remove the tank

To remove the fuel tank from a 1998 Toyota Corolla, follow these steps:

First, jack up the back end of the car to create clearance for removing the fuel tank. It is recommended to use jack stands to ensure the car is steady while it is lifted. Remember to always use extreme caution when working underneath a vehicle that is on a jack. Chock the wheels and set the parking brake if you are jacking up one wheel off the ground.

Next, evacuate the fuel from the gas tank. There is a plug on the bottom of the gas tank that can be removed with a half-inch socket wrench.

Now, locate the straps holding the fuel tank in place. There are two straps running from front to back. Loosen the bolts on the first strap with a socket wrench. There are two bolts for each side of the strap. Do not remove the strap yet. Repeat this process for the second strap.

Place a second jack under the fuel tank and elevate it until it is touching the bottom of the tank. Now you can remove the straps. The tank should be resting on the jack.

Slowly lower the jack until the fuel pump wires are accessible. You should now be able to remove the wires by unplugging them from the top of the tank.

Finally, remove the tank from underneath the vehicle. Lower the car from the jack until the tank is ready to be taken out. Some models may have a shield that needs to be removed to access the fuel tank. The shield is held on by bolts around its edge.

In some cases, you may not need to remove the straps if the tank can slide out from them.

Frequently asked questions