Changing Fuel Filter On Homelite Trimmer: Step-By-Step Guide

If you're looking to replace the fuel filter on your Homelite trimmer, you've come to the right place. This is a step-by-step guide on how to do it. First, drain the gas tank completely. Then, remove the air filter or cylinder cover to access the carburetor. Disconnect the fuel line from the carburetor, reach into the gas tank, and pull out the old fuel filter. Cut off about 6-8 inches of the new fuel line, and insert a metal wire into one end. Push the other end into the hole at the bottom of the fuel tank, and once it's mostly through, grab it with needle-nose pliers and pull it towards the carburetor. Take out the metal wire, and cut off any excess line inside the tank. Insert the tip of the fuel filter into the fuel line, pull the line towards the carburetor, and connect it.

Drain the gas tank

To drain the gas tank of your Homelite trimmer, you will need to start the trimmer and let it run until all the gas in the tank has been used up. This is an important step as it ensures that the gas tank is completely empty before you begin the process of changing the fuel filter.

If your trimmer is unable to start or is not functioning properly, you may need to take it for servicing or repair. In such cases, draining the gas tank may not be possible, and you should seek professional assistance.

Once the trimmer has used up all the gas in the tank, you will need to locate the air filter cover or cylinder cover, depending on the model of your Homelite trimmer. This step is necessary to gain access to the carburetor, which is connected to the fuel tank via the fuel line.

After locating the appropriate cover, use needle-nose pliers to disconnect the fuel line from the carburetor. This step requires caution as you will be working with tools and equipment that may have sharp edges or be sensitive to manipulation. Ensure that you are wearing appropriate protective gear, such as gloves and eye protection, before proceeding.

By following these steps, you will successfully drain the gas tank of your Homelite trimmer and be ready to proceed with changing the fuel filter. Remember to dispose of any old fuel or fuel-related waste in a safe and environmentally friendly manner.

Disconnect the fuel line from the carburetor

Disconnecting the fuel line from the carburetor is a crucial step in changing the fuel filter on your Homelite trimmer. Here is a detailed, step-by-step guide to help you with this process:

To begin, you will need to gain access to the carburetor. Start by removing either the air filter cover or the cylinder cover, depending on the model of your Homelite trimmer. This will expose the carburetor and the fuel line connection.

Now, locate the fuel line, which is a flimsy plastic line that connects the fuel tank to the carburetor. Over time, this plastic line can degrade, so it is important to replace it seasonally or as needed. Once you have located the fuel line, use a pair of needle-nose pliers to carefully grip the fuel line where it connects to the carburetor.

Firmly grasp the fuel line with the needle-nose pliers and gently pull it away from the carburetor. Be careful not to use excessive force, as you do not want to damage the carburetor or any surrounding components.

Once the fuel line is disconnected from the carburetor, set it aside, ensuring that it does not come into contact with any flammable materials. At this point, you can also remove the fuel filter by reaching into the gas tank with the needle-nose pliers and pulling it out, along with the old fuel line. Dispose of these properly.

With the fuel line and fuel filter disconnected and removed, you can now focus on installing the new fuel line and fuel filter. Remember to replace the fuel filter each time you replace the fuel line to ensure optimal performance and prevent future issues.

Remove the old fuel filter

To remove the old fuel filter from your Homelite trimmer, you'll need to first drain the gas tank. Start the trimmer if possible, and let it use up the last of the fuel in the lines.

Once the tank is empty, remove the air filter cover or cylinder cover (this will depend on your model) to access the carburetor. Disconnect the fuel line from the carburetor using a pair of needle-nose pliers.

Now, reach into the gas tank with the needle-nose pliers and pull out the old fuel filter. Dispose of it appropriately.

It is recommended that you replace the fuel line at the same time as the fuel filter. To do this, cut off 6 to 8 inches of new fuel line and cut one end at a 45-degree taper. Insert a metal wire into the other end. Push the tapered end into the hole at the bottom of the fuel tank, using a metal hook to help you gain leverage. Once most of the way through, grab the end with the needle-nose pliers and pull it towards the carburetor.

Remove the metal wire and cut off any excess line inside the tank, leaving about 2 inches. Pull the new fuel line up into the tank a little, so you can insert the tip of the new fuel filter into the line. Pull the line towards the carburetor and connect it to the same spot you removed it from.

Cut the new fuel line to size

To cut the new fuel line to size, you will need to cut off 6 to 8 inches of the new fuel line. Cut one end at a 45-degree angle to create a taper. This tapered end will be inserted into the hole at the bottom of the fuel tank. The angle will make it easier to feed the line through the hole.

Insert a metal wire into the other end of the fuel line. This wire will be used to guide the fuel line through the fuel tank. Push the tapered end of the fuel line into the hole at the bottom of the tank, using a metal hook to help you get leverage. You may need to apply some force to get the line through the hole.

Once the majority of the tapered end is through the hole, grab it with needle-nose pliers and pull it towards the carburetor. At this point, do not connect the fuel line to the carburetor. Instead, remove the metal wire from the other end of the fuel line and cut off any excess line that is inside the tank. You should aim to leave approximately 2 inches of the line inside the tank.

Now, you can pull the fuel line up slightly so that you can insert the tip of the fuel filter into the end of the line. This will connect the fuel filter to the fuel tank.

Insert the new fuel filter

To insert the new fuel filter, pull the new fuel line up into the tank a little so that you can insert the tip of the fuel filter into the fuel line. Then, pull the line towards the carburetor and connect it to the same spot from which you removed the old line.

If you can’t get the line to push through the tank, try coating the outside with a little engine oil to grease it.

Once you have connected the new fuel line and filter, you can refill the fuel tank and start the trimmer.

It is important to replace the fuel filter whenever you replace the fuel line, as a clogged or dirty fuel filter can restrict the flow of fuel to the carburettor, causing the engine to run erratically or stall.

Frequently asked questions