Replacing Fuel Filter In '95 Taurus: Step-By-Step Guide

Changing the fuel filter on a 1995 Ford Taurus is a simple task that can be done in 15-20 minutes. Before starting, park your car on level ground and engage the parking brake. Jack up your car and locate the fuel filter, which is found underneath the vehicle, near the passenger side door, almost directly below the passenger seat. It is a silver or black cylindrical canister with a black hose coming out at both ends.

To change the fuel filter, you will need to relieve the fuel pressure. This can be done by removing the fuel pump relay from the relay box in the engine compartment. Once the engine stops running, you can reinstall the relay but do not restart the car until the fuel filter replacement is complete.

Next, locate the plastic clips that hold the fuel filter in place. Using a flathead screwdriver, push the clips in and then out while pushing the bottom of the clip with your other hand. Once the clips are removed, use a ratchet handle with an extension and a 5/16 socket to loosen the screw holding the fuel filter in place. Separate the hoses from the filter one by one and drain the fuel into a cup.

Now, you can install the new fuel filter. Put the new filter in place and tighten the screw with the ratchet. Reconnect the hoses and put the clips back into place. Finally, turn the key to the on position but do not start the car. Do this 5-10 times to let the new fuel filter fill. You will hear the fuel pump activate. Start the car, and you're done!

Locate the fuel filter

To locate the fuel filter on a 1995 Ford Taurus, park your car on level ground and apply the parking brake. You will need to get underneath your vehicle to find the fuel filter.

The fuel filter is located on the passenger's side of the car, near the passenger side door, almost directly below the passenger seat. It is a cylindrical canister, about three inches in diameter, and is silver or black in colour. It will have a black hose, the fuel line, coming out at both ends.

To access the fuel filter, you will need to jack up your car and get underneath it. It is recommended to use jack stands for safety.

Once you have located the fuel filter, you can proceed to remove it by disconnecting the fuel pump relay and allowing the car to run until it dies. You will then need to remove the three hoses connected to the fuel filter by pushing in and then out on the plastic clips holding them in place. Be sure to have a cup or bucket underneath to catch any spilling fuel.

Disconnect the fuel pump relay

Disconnecting the fuel pump relay is a crucial step in changing the fuel filter on a 1995 Ford Taurus. Here is a detailed, step-by-step guide on how to do it:

Locate the Fuel Pump Relay

The fuel pump relay is part of the Constant Control Relay Module (CCRM) or the Integrated Control Relay Module, which is located in the engine bay. Specifically, you can find it on the center of the firewall, next to the battery, or on the upper radiator support. Refer to your car's manual for the exact location.

• Before you begin, ensure your car is parked on level ground and the parking brake is engaged.
• Open the hood of your Ford Taurus and locate the relay box or the CCRM.
• Identify the fuel pump relay within the relay box or CCRM. It should be labelled, and you can also refer to your owner's manual for help.
• Disconnect the battery ground cable.
• Remove the radiator sight shield, if necessary, to access the CCRM.
• Disconnect the electrical connector from the CCRM.
• Remove the module from the radiator support or the mounting bracket.
• With the fuel pump relay now accessible, proceed to disconnect it.

Release Fuel Pressure (Optional but Recommended)

As an optional but recommended step, you can release the fuel pressure in the lines before proceeding with the fuel filter change. Here's how:

• Locate the fuel pump relay in the relay box or CCRM and remove it.
• Start the engine and let it run until it stops, consuming all the fuel in the lines.
• Reinstall the fuel pump relay but do not restart the car.

By disconnecting the fuel pump relay and optionally releasing the fuel pressure, you have now safely prepared your 1995 Ford Taurus for the fuel filter change. Remember to exercise caution when working with fuel systems and refer to a qualified mechanic if you have any doubts or concerns.

Remove the old fuel filter

To remove the old fuel filter from your 1995 Ford Taurus, first relieve the fuel pressure. This can be done by removing the fuel pump relay from the relay box in the engine compartment. The relay is identified in the owner's manual and can simply be lifted out of the relay panel. Then, start the engine and wait for it to stop running, indicating that the pressure has been relieved.

Next, locate the fuel filter. It is positioned almost directly below the passenger seat on the passenger's side of the fuel tank along the vehicle frame. It is a silver or black cylindrical canister, about three inches in diameter, with a black hose (the fuel line) coming out at both ends.

Now, place a bucket or pan underneath the fuel filter to catch any spilling fuel. There are two plastic clips holding the fuel lines in place. Remove these clips by lightly pushing them in and then out while pushing the bottom of the clip with your other hand. Once the clips are removed, use a ratchet handle with an extension and a 5/16" socket to loosen the screw holding the fuel filter in place.

Finally, separate the hoses from the fuel filter one by one and drain the fuel into the bucket or pan. Be careful not to lay under the car and look up at the filter as you remove the tubes, as fuel may spill out.

At this point, you have successfully removed the old fuel filter and can proceed to install the new one.

Install the new fuel filter

Now that you have removed the old fuel filter, it's time to install the new one.

First, put the new fuel filter in place and tighten the screw with your ratchet. Then, one by one, put the hoses back in place and secure them with the new clips. You should have received new clips with your new fuel filter. If you did not, do not proceed until you have a new set. Do not reuse old plastic clips.

Now, locate the fuel pump kill switch in the trunk and reset it. When you are ready, turn the key to the contact position but do not start the car. Do this 5-10 times to let the fuel filter fill. You will hear the fuel pump activate. Finally, start the car and you're done!

Reset the fuel filter switch

Resetting the fuel filter switch on a 1995 Ford Taurus is a simple task. Here is a step-by-step guide:

• Park your Ford Taurus on level ground and apply the parking brake.
• Locate the fuel pump shut-off switch. For a sedan, it is on the right side of the trunk. For a wagon, it is behind the service panel on the right side of the cargo area.
• Turn the ignition to the OFF position.
• Check the fuel system for any leaks.
• If no leaks are apparent, reset the fuel pump shut-off switch by pushing down on the reset button.
• Turn the ignition to the ON position, wait a few seconds, and then turn it back to the OFF position.
• Perform a final check for leaks in the fuel system.

By following these steps, you will be able to reset the fuel filter switch on your 1995 Ford Taurus safely and effectively. It is important to ensure that there are no fuel leaks before starting the car.

Frequently asked questions