Simple Guide: Replacing Fuel Filter 111P02-0116-F1 In 10 Easy Steps

The Briggs & Stratton 111P02-0116-F1 engine is used in lawn and garden equipment. The fuel filter will either be located inside the fuel tank or fitted into the fuel line between the tank and the fuel pump. To change the fuel filter, you will need to relieve the pressure in the fuel system, disconnect the battery, and jack up your vehicle if the filter is underneath it. Then, use a flat-head screwdriver to pop out the plastic clips holding the fuel filter in place. Next, slide the fuel lines away from the filter and remove them from the nozzles on either end, placing a bowl or bucket underneath to catch any fuel that spills out. You can then slide the old fuel filter out of its bracket. To install a new fuel filter, just slide it into the bracket, reattach the fuel lines, and replace the plastic clips holding the filter in position.

Safety precautions

Changing the fuel filter is a regular part of vehicle maintenance. Here are some safety precautions to follow when changing a fuel filter:

• Relieve the pressure in the fuel system: Before starting any work on the fuel filter, it is important to relieve the pressure in the fuel system. This can be done by locating and removing the fuse for the fuel pump, allowing the engine to run for a short time without a fresh supply of fuel, and then re-inserting the fuse.
• Disconnect the battery: Once the pressure has been relieved, disconnect the negative terminal on the battery to prevent the engine from being started accidentally during the rest of the process.
• Use eye protection and gloves: When working with fuel, it is important to protect your eyes and hands from potential splashes or spills. Wear gloves and eye protection throughout the process.
• Place a bowl or bucket beneath the fuel filter: There may still be fuel left in the lines when you disconnect the fuel filter. Place a bowl or bucket underneath to catch any spills and avoid contamination.
• Jack up the car if necessary: If the fuel filter is located on the underside of the vehicle, you will need to jack up the car to access it safely. Use jack stands to support the vehicle and ensure the car is securely lifted before proceeding.
• Be cautious with plastic containers: Avoid using plastic containers to hold spilled fuel, as it may eat through some types of plastic and cause leaks.
• Avoid mixing fuel with other fluids: Do not mix spilled fuel with oil or coolant. Gasoline should be stored separately in an appropriate container until it can be disposed of or recycled.
• Handle plastic clips with care: The clips holding the fuel filter in place are often made of thin plastic and can break easily. Purchase replacement clips in advance, and if possible, reuse the old clips if they remain intact.
• Secure the vehicle: If you are working underneath the vehicle, ensure it is securely supported and will not roll or shift. Engage the parking brake and place wheel chocks if necessary.
• Work in a well-ventilated area: Fuel fumes can be dangerous, so ensure the work area is well-ventilated to avoid inhaling fumes.
• Dispose of waste properly: Any waste generated during the process, such as used gloves or rags, should be disposed of properly and responsibly.

Locating the fuel filter

Firstly, it is important to understand that the location of the fuel filter depends on whether your engine has a fuel pump or not. For engines without a fuel pump, the fuel filter will typically be located either inside the fuel tank or fitted into the fuel line. This is the case for the Briggs & Stratton 111P02-0116-F1 engine.

Now, let's go through the steps to locate the fuel filter:

• Start by identifying the fuel tank. The fuel filter will either be inside the fuel tank or connected to the fuel line that leads from the tank.
• Carefully examine the fuel tank and look for a small, cylindrical component with a fuel line attached to it. This is usually the fuel filter.
• If you don't see the fuel filter inside the tank, follow the fuel line that leads out of the tank. The fuel filter should be fitted somewhere along this line.
• In some cases, the fuel filter may be located near the engine, so be sure to trace the entire fuel line if you don't find it initially.
• Once you've located the fuel filter, you can proceed with the replacement process, ensuring that you have the correct replacement part for your specific engine model.

Remember to consult the appropriate repair manuals and diagrams for your Briggs & Stratton 111P02-0116-F1 engine, as they will provide detailed visuals and step-by-step instructions specific to your engine model. These resources can be found on the official Briggs & Stratton website or in the owner's manual.

Draining the fuel tank

To drain the fuel tank of the Briggs & Stratton 111P02-0116-F1 engine, follow these steps:

Firstly, ensure you are in a safe area with no open flames or fire sources nearby. This is crucial to prevent any accidents during the process. Wear safety goggles to protect your eyes from liquid fuel or fuel vapors. It is also recommended to have a dry cloth on hand to wipe away any fuel residue and to catch any drips.

Next, locate the fuel valve at the base of the fuel tank, where the gas line is attached. Shut this valve to prevent further fuel flow. If your tank is not equipped with a valve, use a fuel line clamp to clamp the gas line. Avoid pinching the fuel line as this could cause damage.

Now, place a bowl or bucket beneath the fuel filter to catch any fuel that may spill out during the process. This is an important step to avoid fuel spillage and ensure a clean working environment.

If your filter is installed inside the tank, you will need to carefully drain the fuel into the container. Be cautious and move slowly during this step to avoid any accidents or spills. Ensure that the fuel is stored safely and disposed of properly afterward.

Once the tank is drained, you can proceed to remove the fuel filter for inspection or replacement. Remember to always refer to the Briggs & Stratton Engine Operator's manual for detailed instructions specific to your engine model.

Removing the old filter

To remove the old fuel filter, start by relieving the pressure in the fuel system. This can be done by locating and removing the fuse for the fuel pump, starting the engine, and allowing it to run for a minute or two before shutting it off.

Next, disconnect the negative terminal on the battery to prevent accidental engine startup during the procedure. Locate the fuel filter, which is commonly found along the fuel line on the bottom of the car or in the engine bay. If it is located on the underside of the vehicle, jack up the car and place jack stands underneath for safety.

Place a bowl or bucket beneath the fuel filter to catch any fuel that may spill, then remove the clips holding the fuel filter in place using a flat-head screwdriver. With the clips removed, carefully slide the fuel lines away from the filter and tip them towards the bowl or bucket to capture any spilled fuel. Wear eye protection and gloves during this step to protect against fuel splatter.

Finally, slide the fuel filter out of its bracket. The filter is typically held in place by a metal bracket and has a slight bell shape, allowing it to slide out in a specific direction. Some filters may be secured with a bolt that needs to be removed before sliding the filter out.

Installing the new filter

Now that you have relieved the pressure in the fuel system and removed the old fuel filter, it's time to install the new one.

First, compare the new filter to the old one. Make sure they appear to be the same outside diameter, that the nozzles are the same size, and that it will fit into the bracket. If the fuel filters do not match, you will need to return the new one for the correct replacement filter. Do not attempt to use a fuel filter for a different application in your vehicle, as it may not be capable of allowing the appropriate volume of fuel to pass through it.

Next, slide the new fuel filter into the bracket. The new fuel filter should easily slide into its bracket. If you have to force it, it is likely not the correct diameter. The fuel filter should stop when it is seated properly, as it should only be able to slide all the way out in one direction. Be careful not to damage the housing of the fuel filter, as that may cause a leak.

Now, fasten the fuel filter to the fuel line. Slide the fuel lines onto the front and back of the filter the same way they were attached to the old one. With the fuel line in place on the filter, slide the plastic clips through the holes on the fuel line nozzle to secure the line in place on the fuel filter. If the plastic clip breaks as you slide it in, do not attempt to drive the vehicle until you replace the broken clip. Make sure the fuel lines are snug on the nozzles of the fuel filter before sliding the clips into place.

Finally, lower the vehicle off of the jack stands. Jack up the car to relieve the weight on the jack stands, then slide them out from beneath the vehicle. Once the jack stands are clear, lower the vehicle to the ground. Be sure the jack stands are completely out of the way, otherwise they may damage the vehicle if lowered onto them. Once the vehicle is safely on the ground, reconnect the battery to complete the project.

Frequently asked questions