Replacing Fuel Pump In Craftsman Push Lawn Mower

The fuel pump is an essential component of a lawnmower, powering the machine by pumping fuel from the gas tank to the carburetor. If your Craftsman push lawn mower is experiencing issues, you may need to locate and replace the fuel pump. To do this, refer to your owner's manual to locate the pump, which is typically next to the gas tank and connected to the tank and carburetor via rubber tubes. Once located, put on protective gear and disconnect the spark plug, followed by the fuel pump itself. Next, inspect the pump for damage, and if necessary, source replacement parts from the manufacturer. Finally, reconnect the new fuel pump to the mower.

Locating the fuel pump

To locate the fuel pump on your Craftsman push lawn mower, start by referring to the owner's manual. There should be a diagram in the manual that illustrates where all the parts are located. Typically, the fuel pump is found next to the gas tank and is connected to the tank and the carburetor by rubber gas tubes.

The fuel pump is used when the gas tank is mounted lower than the carburetor, and gravity cannot be relied on to carry gas through the fuel line. The pump is typically mounted on the carburetor, near the fuel tank, or between the tank and the carburetor.

Briggs & Stratton pulse-type fuel pumps, for example, have either a plastic or metal body. They develop pressure using the varying vacuum in the crankcase or off the intake manifold, which is created by the motion of the piston and the operation of the crankcase breather. A fitting on the crankcase cover, the dipstick tube, or the intake manifold uses the pulse of air to move the diaphragm and check valves to draw fuel from the fuel tank and into the carburetor.

Disconnecting the spark plug

Before you begin, put on protective gear. This is important for your safety and should not be skipped.

Now, locate the spark plug. It will be connected to the engine by a thick wire. Once you have found it, disconnect this wire. You can do this by pulling or squeezing the connector. If you are having trouble, use a pair of pliers to gently loosen the connector and pull it off. Make sure that the wire does not touch any metal parts of the engine, as this could cause an accidental spark.

With the spark plug disconnected, you can now safely move on to the next step of disconnecting the fuel pump.

Disconnecting the fuel pump

To disconnect the fuel pump on your Craftsman push lawn mower, follow these steps:

First, put on protective gear and disconnect the spark plug to ensure the mower doesn't accidentally turn on. This is an essential step for your safety.

Next, locate the fuel pump. Typically, it is found next to the gas tank and has rubber gas tubes connecting it to the tank and the carburetor. Refer to your owner's manual for a diagram of the mower's components.

Once you've located the fuel pump, use a screwdriver and pliers to disconnect it. You may need to use needle-nose pliers to loosen the clips on the fuel hoses. After disconnecting the fuel pump, remove it from the mower by unscrewing the mounting screws and lifting it out of its housing.

Now that the fuel pump is disconnected and removed, you can proceed to inspect it for any damage or wear and tear. Use your screwdriver to carefully disassemble and inspect the individual parts, such as gaskets, diaphragms, and seals. Ensure you clean any dirt or debris from the pump during this process.

Inspecting the fuel pump for damage

Locate the Fuel Pump: The fuel pump on your Craftsman push lawn mower is typically found next to the gas tank. It is connected to the tank and the carburetor by rubber gas tubes. Refer to your owner's manual for a diagram of the mower's components.

Disconnect and Remove the Fuel Pump: Before beginning, put on protective gear and disconnect the spark plug to ensure the mower is powered off. Use a screwdriver and pliers to disconnect and remove the fuel pump.

Inspect for Damage: Once the fuel pump is removed, thoroughly inspect it for any signs of damage. Normal wear and tear can be expected, especially after extended use. Use a screwdriver to disconnect the pump's parts for a closer examination. Pay attention to the gaskets, diaphragms, seals, and other mechanisms, as damage to these components may require replacement. Clean any dirt or debris from the pump during this process.

Check for External Damage: Examine the external surfaces of the pump for hairline cracks or other signs of damage. If the pump has a metal body and exhibits any cracks, it should be discarded, and a replacement should be performed.

Internal Damage Inspection: If the pump has a plastic body or no visible external damage, proceed to inspect the internal components. Disassemble the pump, following any relevant manufacturer guidelines, and soak metal parts in an all-purpose parts cleaner for up to 15 minutes.

Examine the Hoses: Check the hoses for any signs of cracking, softening, or hardening. Replace any worn or damaged hoses to ensure proper fuel flow.

Overall, inspecting the fuel pump for damage involves a combination of visual inspection, disassembly, and cleaning. By carefully examining the external and internal components, you can identify issues that may require repair or replacement, ensuring the safe and proper functioning of your Craftsman push lawn mower.

Replacing the fuel pump

The fuel pump is an essential component of a lawnmower. It pumps fuel from the gas tank to the carburetor, which powers the lawnmower. It is usually located next to the gas tank and is connected to the tank and the carburetor by rubber gas tubes.

To replace the fuel pump on your Craftsman push lawn mower, first put on protective gear and disconnect the spark plug to ensure that the mower won't turn on. Then, disconnect and remove the old fuel pump using a screwdriver and pliers. Examine the old fuel pump for any signs of damage. Normal wear and tear may be observed, especially after years of regular use.

Once the old pump is removed, you can install the new fuel pump. Place the diaphragm spring and then the cup over the center of the pump chamber. Also, insert a valve spring. Install the diaphragm, gasket, and cover and attach them with pump screws. Tighten the screws using a torque wrench. Finally, attach the pump to the carburetor or mounting bracket using the pump mounting screws.

After you have finished the installation, reconnect the fuel pump to the mower, including the rubber gas tubes to the tank and the carburetor. Always run the engine after installing a new pump or performing a repair to verify that there are no leaks.

Frequently asked questions