Replacing Fuel Pump In 2007 Ford Edge: Step-By-Step Guide

The fuel pump in a 2007 Ford Edge is located inside the fuel tank and has a small electric motor to ensure that pressurised gasoline flows to the engine to power the vehicle. The pump delivers the right amount of fuel at a high enough pressure to keep the engine running smoothly. The cost of replacing a fuel pump in a 2007 Ford Edge is estimated to be between $1,259.42 and $1,779.32, with labour costs between $307 and $387, and parts between $1,393 and $1,558.

Disconnect the battery

Disconnecting the battery is the first step in replacing the fuel pump in a 2007 Ford Edge. This is a crucial safety precaution to reduce the chance of a fire occurring during the procedure.

Before beginning any work on the fuel pump, make sure you have the correct tools and safety equipment. Wear protective gear, such as gloves and eye protection, to safeguard against any potential hazards. Ensure you have a suitable container for any fuel that needs to be drained.

Locate the battery in your Ford Edge. It is usually found in the engine bay, towards the front of the vehicle. The battery is a rectangular unit with two terminals, a positive and a negative, protruding from the top. These terminals are connected to the battery cables, which supply power to the electrical systems of the car.

To disconnect the battery, you will need to remove these cables from the terminals. Start by loosening the nut or bolt that secures the negative cable (usually black) to the negative terminal, using the appropriate-sized wrench or socket. Once loose, carefully pull the cable away from the terminal. You may need to wiggle it gently to detach it. Place the cable to one side, ensuring it does not touch any metal parts of the car.

Next, repeat the process for the positive cable (usually red). Loosen the nut or bolt securing it to the positive terminal, then remove the cable. Ensure that the positive cable does not touch any metal parts of the car, as this could cause a short circuit.

With both cables detached, you have successfully disconnected the battery. You can now proceed with the next steps of the fuel pump replacement process, which may include draining fuel, removing the fuel tank, and accessing the pump through an access panel. Remember to work cautiously and refer to a qualified mechanic if you are unsure about any part of the procedure.

Remove the access cover

To remove the access cover of your 2007 Ford Edge's fuel pump, you will first need to disconnect the battery to reduce the chance of a fire.

Next, locate the access cover. The fuel pump is located inside the fuel tank, so the access cover will be found above the tank in the passenger compartment. Once you have located the access cover, remove it.

If there is no access panel, you will first need to drain the fuel from the tank before removing the fuel tank from the vehicle to gain access to the pump.

Once the access cover is off, you will be able to replace the fuel pump and pre-pump filter screen.

Replace the pump and pre-pump filter screen

To replace the pump and pre-pump filter screen of a 2007 Ford Edge, you will need to follow these steps:

Firstly, disconnect the battery to reduce the chance of a fire. Next, gain access to the pump. If the pump is inside the fuel tank, remove the access cover. If the pump is outside the tank, disconnect the fuel lines and remove the pump. In some cases, you will need to drain the fuel before removing the access panel. Once you have access to the pump, remove the fuel pump supply and return hoses, EVAP system hoses, and electrical connections.

Now you can install the new pump. Attach any reusable brackets and pick-up screens to the new pump, and then insert it into the fuel tank or connect the fuel lines, depending on your vehicle's setup. If your fuel system uses an in-line external filter, it is recommended to replace it at this time. Re-establish all hoses and electrical connections.

Finally, add fuel to the tank and run the engine to test for leaks. Check for fuel leaks or odors before starting or driving the car. If you notice any leaks or smell gasoline, do not start the engine and have the car towed to a repair shop.

Reconnect the fuel lines

To reconnect the fuel lines of your 2007 Ford Edge, follow these steps:

Firstly, ensure that the fuel pump supply and return hoses, as well as any EVAP system hoses, are properly connected. These hoses play a crucial role in the fuel system, so it is important to check that they are securely attached.

Next, re-establish all electrical connections to the fuel pump. As a safety precaution, it is recommended to disconnect the battery before beginning any work involving the fuel system. Once all the electrical connections are secure, you can reconnect the battery.

After reconnecting the fuel lines and electrical components, it is necessary to refill the fuel tank. Running the engine after refuelling will allow you to test for any potential leaks in the system and ensure that the problem has been resolved.

It is worth noting that fuel pump replacement is a complex task best left to professionals. Working with the fuel system can be dangerous, so taking all necessary precautions to prevent fires is crucial. Additionally, it is recommended to replace the fuel filter at the same time as the fuel pump to ensure optimal performance and reduce the risk of future issues.

By carefully following these steps and paying attention to safety measures, you can successfully reconnect the fuel lines and restore the functionality of your 2007 Ford Edge's fuel system.

Check for fuel leaks

When replacing the fuel pump in a 2007 Ford Edge, it is important to check for fuel leaks. Fuel leaks can be dangerous and can lead to a fire, so it is important to take the necessary precautions. Here are some detailed instructions on how to check for fuel leaks:

Before beginning any work on the fuel pump, it is important to disconnect the battery to reduce the chance of a fire. This is a critical step to ensure your safety. Once the battery is disconnected, you can proceed with the fuel pump replacement process.

If the fuel pump is located inside the fuel tank, you will need to remove the access cover to gain access to the pump. In some cases, you may need to drain the fuel before removing the access panel. With the cover off, proceed to replace the pump and the pre-pump filter screen.

If the pump is located outside the tank, disconnect the fuel lines, remove the pump, and install the new one. Ensure that any reusable brackets and pick-up screens are attached to the new pump.

Once you have replaced the fuel pump, the next step is to check for fuel leaks. Add fuel to the tank and run the engine. Keep an eye out for any leaks or odors. If you notice any fuel leaks or smell gasoline, do not start or drive the car. Do not park the car inside your house or under a covered structure. Instead, have the car towed to a repair shop for further inspection and repair.

It is important to take all necessary precautions when working with the fuel system to prevent the risk of fire. Make sure to follow the instructions carefully and seek professional help if you are unsure about any steps.

Frequently asked questions