Replacing Fuel Pickup Sock In 2000 Accord V-6: Step-By-Step Guide

If you're looking to replace the fuel pickup sock on your 2000 Honda Accord V6, you'll first need to lower the gas tank and the entire rear suspension. This is a complex process that may be best left to a professional mechanic. However, if you're determined to do it yourself, you'll need to remove the carpet from the trunk, disconnect the electrical connector, and crank the car for about 30 seconds to relieve fuel pressure. Be sure to work in a well-ventilated area to avoid inhaling harmful gas fumes.

Remove the carpet from the trunk

To remove the carpet from the trunk of a 2000 Honda Accord V6, follow these steps:

Firstly, before you lift the car, you must remove the carpet from the trunk. This will expose the fuel pump access panel, which you should also remove. Next, disconnect the electrical connector and crank the car for around 30 seconds to relieve the fuel pressure.

Now, disconnect both fuel lines from the fuel pump through the access panel in the trunk. Be careful when performing this step, as the fuel lines will be rusty. The plastic lines run above the tank and are held in place with plastic clips.

Once you have disconnected the fuel lines, you can then carefully lower the sub-frame. As soon as you are able to, pull the lines out of the clips and remove the evap lines.

Removing the carpet from the trunk is the first step in replacing the fuel pickup sock on a 2000 Honda Accord V6.

Disconnect the electrical connector

Disconnecting the electrical connector is one of the first steps to replacing the fuel pickup sock on a 2000 Honda Accord V-6. Here is a detailed, step-by-step guide on how to do this:

Before you begin, it is important to ensure you are working in a well-ventilated area as you will be dealing with fuel and gas fumes, which can be harmful.

Now, to disconnect the electrical connector, follow these steps:

Step 1: Remove the carpet from the trunk of the car. This will give you access to the fuel pump access panel.

Step 2: Locate the fuel pump access panel. This is where you will find the electrical connector.

Step 3: Disconnect the electrical connector. It is important to do this before lifting the car or attempting to remove any fuel lines.

Step 4: Crank the car for around 30 seconds to relieve the fuel pressure. This will make it easier and safer to work on the fuel system.

Step 5: Disconnect both fuel lines from the fuel pump through the access panel in the trunk. Be careful when doing this, as the fuel lines and fittings may be rusty and fragile.

By following these steps, you will successfully disconnect the electrical connector and can proceed to the next steps of replacing the fuel pickup sock. Remember to work in a well-ventilated area and exercise caution when working with any fuel or electrical components.

Crank the car to relieve fuel pressure

Cranking the car to relieve fuel pressure is an important step when replacing the fuel pickup sock on a 2000 Accord V-6. Here is a detailed, step-by-step guide on how to perform this procedure:

Before you begin, ensure you have the necessary tools and safety equipment, such as gloves and eye protection, as you will be working with fuel. It is also recommended to work in a well-ventilated area to avoid inhaling gas fumes.

Step 1: Open the car's trunk and remove the carpet lining to access the fuel pump. This will expose the fuel pump access panel.

Step 2: Disconnect the electrical connector from the fuel pump. This is usually located near the fuel pump access panel.

Step 3: Crank the car for approximately 30 seconds to relieve the fuel pressure. This is a crucial step to ensure that the fuel system is depressurized before proceeding with any repairs or maintenance. Make sure to perform this step before disconnecting the fuel lines.

Step 4: With the car still running, carefully disconnect both fuel lines from the fuel pump through the access panel in the trunk. Be cautious as the fuel lines may be under pressure, and have a rag handy to wipe up any spilled fuel.

Step 5: Once the fuel lines are disconnected, turn off the car and remove the ignition key.

Step 6: Continue with the rest of the fuel pickup sock replacement procedure as outlined in the repair manual or other instructions.

It is important to note that relieving fuel pressure by cranking the car is just one method. Alternatively, you can relieve fuel pressure by removing the gas cap or loosening the gas pressure bolt at the end of the fuel rail. However, make sure to re-tighten the bolt once the job is finished if you choose the latter option.

Disconnect the fuel lines

To disconnect the fuel lines of a 2000 Honda Accord V6, you must first relieve the fuel system pressure. Remove the gas cap to relieve the gas pressure from the fuel system. You can also loosen the gas pressure bolt at the end of the fuel rail.

Next, locate the fuel pump access panel in the trunk and disconnect both fuel lines from the fuel pump. The plastic lines run above the tank and are held in place with plastic clips. Be careful when disconnecting the lines, as they will be rusty and difficult to remove.

Once the lines are disconnected, you will need to lower the sub-frame. As you lower it, wiggle it to prevent it from getting stuck on the front body to sub-frame bushings.

After the sub-frame is lowered, you can access the fuel tank. The fuel tank is held in place with straps that are bolted to the sub-frame. Remove at least one bolt from each strap to release the tank.

With the tank released, you can now access the fuel pump and fuel lines. Carefully disconnect the fuel lines from the fuel pump, taking care not to damage the connectors.

It is important to work in a well-ventilated area when performing this task, as gas fumes can be harmful.

Remove the exhaust

To remove the exhaust from a 2000 Honda Accord, follow these steps:

Prepare the car for exhaust removal

As a safety precaution, allow the exhaust to cool completely before installing a new one. Disconnect the negative terminal (black cover) of your car battery. This ensures the car reprograms itself to accommodate the new exhaust. Jack up the car on all four corners of the frame and secure it with jack stands.

Remove the stock exhaust system

When removing the stock exhaust system, work from the back (exhaust tip, muffler, and rear exhaust pipe) to the front (catalytic converter, exhaust down pipe, and manifold). Using a 10mm socket and ratchet, remove the three bolts securing the rear exhaust pipe to the muffler. Then, remove the muffler and rubber flange, which seals the connection between the exhaust muffler and the rear exhaust pipe. Set the rubber flanges aside as they will be reused for the new exhaust. With a 14mm socket and ratchet, remove the three bolts connecting the rear exhaust pipe to the converter. Remove the rubber flange in between the pipe and converter. Set it aside. Lift the exhaust system off the hangers if necessary, and set it aside for the new exhaust installation.

Install the new cat-back exhaust

To install the new cat-back exhaust, simply follow the previous steps in reverse order, working from the front of the car to the rear. Lift and rest the new rear exhaust pipe onto the hangers. Place the rubber flange in between the converter and exhaust pipe, and bolt them together with the 14mm socket and ratchet. Place the other rubber flange in between the rear exhaust pipe and the muffler, and bolt them together with the 10mm socket and ratchet. Re-inspect the cat-back to ensure all bolts are secure. Lower the car and confirm that the new exhaust sounds and runs smoothly.

Note: To access the fuel pickup sock in a 2000 Honda Accord V6, you will need to remove the fuel tank. This involves siphoning out the gas tank, raising and securing the car, disconnecting the fuel-sending unit and fuel lines, removing the tank straps, and then slowly lowering the tank.

Frequently asked questions