Replacing The Fuel Line On Your Homelite Blower: A Guide

If you're looking to replace the fuel line on your Homelite blower, you've come to the right place. This step-by-step guide will walk you through the process, but before you begin, make sure you have the correct size lines for your specific blower model. The replacement process typically involves removing the blower tube, air filter cover, carburetor, and fuel tank to access the fuel lines. It is crucial to disconnect the spark plug wire to prevent accidental starting during the procedure. Once you have accessed the fuel lines, carefully remove the old lines and install the new ones, ensuring proper routing and secure connections. Additionally, it is recommended to replace the fuel filter and clean the fuel tank during this process.

Drain the fuel tank

To drain the fuel tank of your Homelite blower, you'll need to find a well-ventilated area to work in. Start by removing the fuel cap and emptying the fuel from the tank into an approved storage container. You can use paper towels or shop rags to catch any spills or leaks.

It's important to note that fuel can be dangerous, so ensure you are wearing appropriate protective gear and taking the necessary safety precautions.

Once the tank is empty, you can move on to disconnecting the spark plug wire and removing the blower tube, air filter cover, carburetor, and fuel tank, as outlined in the next steps of the fuel line replacement process.

However, if you are solely focused on draining the fuel tank, the above steps should be sufficient to safely and effectively complete the task.

Disconnect the spark plug wire

Disconnecting the spark plug wire is an important step when replacing the fuel line on a Homelite blower. This step ensures that the blower cannot start accidentally during the repair process, which could be hazardous.

To disconnect the spark plug wire, locate the spark plug on your Homelite blower. It is usually found near the engine or the carburetor. Once you have located the spark plug, follow the wire attached to it. The wire will typically be connected to the spark plug via a boot or connector.

To disconnect the wire, simply pull or twist it gently away from the spark plug. In some cases, there may be a clip or clamp holding the wire in place, which you can carefully unfasten. Make sure not to damage the wire during this process. Once the wire is disconnected, set it aside in a safe place where it will not cause any obstruction while you work on replacing the fuel line.

It is important to note that before performing any maintenance or repairs on your Homelite blower, you should always refer to the owner's manual for safety precautions and instructions. Additionally, allow the engine to cool down before attempting to disconnect the spark plug wire or perform any other maintenance or repair work.

Remove the carburetor

To remove the carburetor from your Homelite blower, you will first need to disconnect the spark plug wire to ensure the leaf blower can't start. Then, remove the blower tube by loosening the thumb screw on the front of the housing and pulling the tube off. Next, remove the air filter cover by unscrewing the screws and lifting it off.

Now, you can access the carburetor. Remove the carburetor mounting screws and carefully pull out the air box, releasing it from the carburetor throttle and choke levers. Note the configuration of the small and large fuel lines so that you can reconnect them correctly later. Detach the fuel lines from the carburetor and then remove the carburetor from the engine.

At this point, you will need to remove the carburetor adapter and air dam. Unscrew the screws from the carburetor adapter and pull the adapter and air dam off the engine.

To reinstall the carburetor, push the fuel lines back onto the proper connections and insert the carburetor into the air box, ensuring the throttle and choke levers are positioned correctly. Secure the carburetor in place with the mounting screws. Finally, reinstall the air filter cover.

Remove the fuel tank

To remove the fuel tank from your Homelite blower, first empty the fuel from the tank into an approved storage container. Then, disconnect the spark plug wire to ensure the blower can't start. Next, remove the blower tube by loosening the thumb screw on the front of the housing and pulling the tube off.

Now, you need to remove the left side of the housing. To do this, remove the screws from the right side of the housing. The fan cover and handle will come off with the housing. Once the housing is removed, you can take out the fuel tank.

At this point, you can pull the fuel lines out of the tank. Use needle-nose pliers to remove the fuel filter from inside the tank, and then pull out the small fuel line. Finally, push the large fuel line into the tank and pull it out through the mouth of the tank.

Pull the fuel lines out of the tank

To pull the fuel lines out of the tank, you will need needle-nose pliers. The end of the small fuel line is connected to the fuel filter inside the tank. Use the needle-nose pliers to fish the fuel filter out of the mouth of the tank. Once you have removed the fuel filter from the end of the small fuel line, pull the small fuel line out of the tank through the mounting hole.

Now, push the large fuel line into the tank through the mounting hole and pull it out of the mouth of the tank.

Before you begin this process, ensure you have removed the fuel tank from the housing. To do this, remove the screws from the front of the muffler guard cover and pull the guard cover off the muffler. Then, remove the blower tube thumb screw from the front of the housing. Next, remove the screws from the right side of the housing and pull the left side of the housing off the blower. The fan cover and handle will come off with the housing. Finally, remove the fuel tank from the housing.

When you have finished pulling the fuel lines out of the tank, you can install the new large fuel line. Cut one end of the new large fuel line at an angle and push the angled end into the tank through the mounting hole. Ensure you push it far enough that you can grab the end through the mouth opening with needle-nose pliers. Now, cut the angled end of the large fuel line square and install the grommet on the end. Tug the opposite end of the large fuel line until the grommet touches the side of the tank. Finally, cut the large fuel line to the same length as the original large fuel line.

Frequently asked questions