Replacing Fuel Door Spring On 2007 Envoy: Easy Steps

If the fuel door on your 2007 GMC Envoy is faulty, you may need to replace the spring. This is a fairly simple task that can be done by following these steps: First, open the fuel door and remove the bolts holding the hinge to the body. Then, move the hinge towards the door and pry out the old spring with a flathead screwdriver. Finally, insert the new spring and bend the tab back so that it catches the release cable. This process should only take around 10 minutes and can be done without removing the fuel door, although some people find it easier to remove the door to clean the filler area and the back of the door.

Removing the fuel door

To remove the fuel door of a 2007 GMC Envoy, you will need to remove the hinge that connects the door to the body of the car. First, locate the bolts that hold the hinge in place. There should be two bolts that are visible on the lip to the left of the fuel door opening. Use a screwdriver or socket to remove these bolts. Once the bolts are removed, you can carefully lift the fuel door off of the hinge. Be sure to lift the door straight up, as you do not want to accidentally pry the hinge and door apart. If the hinge and door do become separated, you will need to realign them before reinstalling the door.

If the hinge and door are still connected, you can now move on to removing the hinge itself. The hinge is held in place by two 8mm bolts. Use an 8mm socket or a Phillips-head screwdriver to remove these bolts. With the bolts removed, you can now lift the hinge out of its housing. Again, be careful not to pry the hinge and door apart.

Once the hinge is removed, you can clean any dirt or debris from the hinge and door mechanism. Reattach the hinge to the body of the car using the same bolts that you removed earlier. Tighten the bolts securely, but be careful not to over-tighten them as this can damage the threads or strip the bolt heads.

Finally, reattach the fuel door to the hinge. Line up the holes in the door with the hinge and slide it into place. You may need to apply a small amount of pressure to fully seat the door on the hinge. Once the door is in place, test it to make sure it opens and closes smoothly. If the door is functioning properly, your job is done!

Unscrewing the bolts

Locate the Bolts: Begin by opening the fuel door. You will find the bolts that hold the hinge to the body of the car. Typically, there are two bolts securing the hinge in place.

Gather the Right Tools: Before you start, make sure you have the appropriate tools to unscrew the bolts. In this case, you will need an 8mm socket or a Phillips-head screwdriver. Having the right tools ensures that you can efficiently and safely remove the bolts without damaging them or the surrounding components.

Removing the Hinge: Once the bolts are completely unscrewed, you can remove the hinge by simply lifting it or wiggling it gently to detach it from the body. Be cautious during this step to avoid misplacing or losing the bolts, as you will need them again when installing the new fuel door spring.

At this point, you have successfully unscrewed the bolts and removed the hinge, and you can proceed to the next steps of replacing the fuel door spring. Remember to keep the bolts and screws in a safe place so that you can reassemble everything securely later.

This process should help you safely and effectively unscrew the bolts related to the fuel door spring of your 2007 GMC Envoy.

Cleaning the filler area

To clean the filler area of your 2007 GMC Envoy, you will first need to remove the fuel door. This will require you to open the fuel door and locate the bolts holding the hinge to the body of the car. There should be two bolts, which can be removed using an 8mm socket or a Phillips-head screwdriver. Once these bolts are removed, you can take off the entire hinge and door assembly.

With the fuel door removed, you can now access the filler area to clean it. Use a soft cloth or brush to wipe down the area, removing any dirt, dust, or debris that has accumulated over time. Be gentle and avoid using abrasive materials or chemicals, as these may damage the paint or finish.

If the filler area is particularly dirty or has stubborn grime, you can use a mild soap or detergent mixed with water to help loosen and remove the buildup. Apply the soapy water with a soft cloth and work it into the affected areas. Then, use a damp cloth to wipe away the soap residue and dry the area thoroughly afterward.

It is also important to clean the back of the fuel door itself. Use a similar process as above, wiping it down with a soft cloth and mild soap if needed. Ensure that the door is completely dry before reattaching it to the vehicle.

Once you have finished cleaning the filler area and the back of the fuel door, you can proceed to reinstall the fuel door. Carefully align the hinge and door assembly back into place and secure it with the bolts you removed earlier. Test the fuel door to ensure it opens and closes smoothly.

Installing the new spring

To install the new spring, you will need to first open the fuel door. If your fuel door release cable is broken, you may need to bend the tab on the fuel door so that it can be opened manually. Once the fuel door is open, remove the two 8mm bolts holding the hinge to the body of the car. Move the hinge towards the door and use a flathead screwdriver to pry out the old spring.

Now, take your new spring and engage the hook tab first, then push on the other side by the vertical hinge pin. It should pop right in. Make sure the spring is securely in place before reattaching the fuel door.

If you are having trouble getting the new spring in place, you can try using a piece of rope or string. Place the spring into the correct spot nearest to the hinge and loop the rope over the other end of the spring. Pull on the rope to guide the other end of the spring into the correct position.

Finally, check that your gas door opens and closes properly and enjoy not having to bring a screwdriver to your next fill-up!

Reattaching the fuel door

To reattach the fuel door of a 2007 GMC Envoy, you will need to first open the fuel door. Then, remove the two 8mm bolts that are holding the hinge to the body of the car. Once these are removed, you can take off the entire hinge and door unit.

Next, you will need to move the hinge towards the door and use a flat-head screwdriver to pry the old spring clip out. Be careful not to scratch or damage the fuel door or hinge during this process. It may be helpful to clean the inside of the fuel door and hinge before proceeding to the next step.

Now, take your new spring and engage the hook tab first. Then, push on the other side of the spring by the vertical hinge pin until it pops into place. You can also use a pair of needle-nose pliers to help pull the spring into place if needed. Ensure that the spring is securely attached to the hinge and fuel door.

Finally, reattach the fuel door and hinge to the body of the car by screwing in the two bolts that you removed earlier. Open and close the fuel door a few times to test that it is functioning properly and that the spring is holding it in place.

Frequently asked questions