Fuel Pressure And Banjo Bolt Adapters: Installation Tips

If you're looking to install a fuel pressure gauge, a banjo bolt adapter can make the process easier. This adapter replaces your stock banjo bolt, allowing you to install the fuel pressure sending unit directly onto the fuel filter housing. The banjo bolt adapter has a 1/8-27 NPT Female to Male 90 Degree Elbow, which provides a more accessible position for the fuel sensor. When installing the adapter, it's important to ensure that you don't torque more than 20 foot-pounds.

Banjo bolt thread adapter for Honda vehicles

If you're looking to install a fuel pressure gauge on your Honda, a banjo bolt thread adapter is a great solution. This adapter replaces the stock banjo bolt on your Honda's fuel filter housing, allowing you to install a fuel pressure sending unit or sensor directly.

The GlowShift Fuel Pressure Banjo Bolt Thread Adapter, designed specifically for Honda vehicles, features a thread size of M12 x 1.25" and a 1/8-27 NPT Female-to-Male 90 Degree Elbow. This elbow provides a more accessible position for the fuel pressure sender. It is built for durability, made from Mild Steel with Yellow Zinc plating. It is important to note that you should not torque this adapter more than 20 foot-pounds during installation.

The Banjo Bolt Thread Adapter is compatible with a range of Honda and Acura vehicles, including:

• 1988-1991 Honda Civic/CRX (All Models)
• 1992-2000 Honda Civic (All Models)
• 1993-1997 Honda Del Sol
• 1992-1996 Honda Prelude (All Models)
• 2000-2003 Honda S2000
• 1990-2001 Acura Integra (All Models, including Type-R)
• 1991-2000 Acura NSX (All Models)

Additionally, it is compatible with any fuel filter that uses an M12 x 1.25" banjo bolt.

To install the GlowShift Fuel Pressure Banjo Bolt Thread Adapter, follow these steps:

• Remove the stock banjo bolt from the top of the fuel filter housing.
• Remove the old crush washers from both sides of the fuel line.
• Connect the fuel line to the banjo bolt adapter, placing a crush washer on each side of the fuel line.
• Thread the banjo bolt adapter into the top of the fuel filter housing, ensuring you do not torque more than 20 ft. lbs.
• Install the fuel pressure sensor into the 90-degree elbow fitting and then install this assembly into the female end of the banjo bolt adapter.

With this banjo bolt thread adapter, you can easily fuel pressure on your Honda vehicle without major modifications.

Banjo bolt sensor thread adapter for Honda and Acura vehicles

If you're looking to install a fuel pressure gauge on your Honda or Acura vehicle, a banjo bolt sensor thread adapter is a great option. This adapter replaces the stock banjo bolt, allowing you to install the fuel pressure gauge directly onto the fuel filter housing.

The GlowShift Fuel Pressure Banjo Bolt Thread Adapter is a popular choice for Honda and Acura vehicles. It features a female 1/8-27 NPT to male M12 x 1.25 thread, a 90-degree elbow, and is made from mild steel with yellow zinc plating for durability. It is compatible with a range of Honda and Acura models, including the Honda Civic, Del Sol, Prelude, S2000, and Acura Integra, NSX, and more.

The installation process is straightforward. First, remove the stock banjo bolt from the top of the fuel filter housing, along with the old crush washers from both sides of the fuel line. Then, connect the fuel line to the banjo bolt adapter, placing a crush washer on either side of the fuel line. Thread the adapter into the fuel filter housing, being careful not to torque more than 20 foot-pounds. Finally, thread the fuel pressure sensor into the 90-degree elbow fitting and install it into the female end of the banjo bolt adapter.

The banjo bolt sensor thread adapter provides an accessible position for the fuel pressure sensor and ensures an accurate reading of the fuel pressure in your Honda or Acura vehicle. It is a useful tool for anyone looking to monitor their vehicle's fuel system performance.

Banjo bolt sensor thread adapter for Dodge Ram trucks

If you own a Dodge Ram truck, you may need to use a banjo bolt sensor thread adapter to fuel your vehicle. This adapter is designed to replace your truck's stock banjo bolt, allowing you to install a fuel pressure sending unit directly to the fuel filter housing. This process involves a few simple steps:

First, remove the stock banjo bolt from the bottom of the fuel filter housing, as well as the crush washers from both sides of the fuel line. Then, thread the banjo bolt adapter into the bottom of the fuel filter housing and torque it to the specified number of foot-pounds using a wrench. Finally, install the fuel pressure sensor into the female end of the banjo bolt adapter.

It is important to note that the thread size for this banjo bolt is M12 x 1.5, and it includes two crush washers that are 0.46 inches in diameter. When installing the adapter, do not torque more than 18 foot-pounds to avoid damage.

The banjo bolt sensor thread adapter is compatible with the 1998.5-2010 Dodge Ram 24-Valve 5.9L Cummins. It features a 1/8-27 NPT female thread port, allowing for easy installation of a fuel pressure sensor. With this adapter, you can conveniently monitor your fuel pressure and ensure the optimal performance of your Dodge Ram truck.

Banjo bolt sensor thread adapter for P7100 12-valve Dodge Ram trucks

The Banjo Bolt Sensor Thread Adapter is a highly useful tool for owners of 1994-1998 Dodge Ram P7100 12-valve trucks. This adapter replaces the stock banjo bolt, allowing access to the injection pump for accurate fuel pressure readings.

The Banjo Bolt Sensor Thread Adapter is designed to be durable, with a tough zinc plating that will last as long as your Cummins diesel engine. It features a male M14 x 1.5 thread that installs into the P7100 injection pump and a female 1/8-27 NPT thread for a snubber valve or fuel pressure sensor. The adapter also comes with two 14mm diameter crush washers that fit securely over the banjo fitting.

To install the Banjo Bolt Sensor Thread Adapter, simply remove the stock banjo bolt from the inlet side of the injection pump, along with the crush washers from both sides of the fuel line. Then, place the fuel line onto the Banjo Bolt Adapter and thread the adapter into the injection pump, torquing it to 18 foot-pounds. Finally, install the fuel pressure sensor into the snubber valve and then into the female end of the Banjo Bolt Adapter.

GlowShift, the manufacturer of this adapter, provides detailed instructions and free lifetime technical support to make the installation process easy. With this adapter, you'll be able to connect to your fuel pressure gauge and start taking readings in no time!

Banjo bolt sensor thread adapter for 24-valve Dodge Ram trucks

The GlowShift Fuel Pressure Banjo Bolt Sensor Thread Adapter is designed for 24-valve Dodge Ram trucks. It replaces the factory bolt, allowing users to install a 1/8-27 NPT fuel pressure sensor to the fuel filter housing. This banjo bolt adapter fits the 1998.5 to 2007.5 Dodge Ram 24 Valve 5.9 Cummins on both the inlet side of the injection pump and the fuel filter housing.

The adapter is made from carbon steel with a nickel-zinc coating, or mild steel with a zinc plating, and comes with two crush washers. It has a thread size of Female 1/8-27 NPT to Male m12 x 1.5. It should be torqued to no more than 18-20 foot-pounds.

To install the adapter, first remove the stock banjo bolt from the bottom of the fuel filter housing, also removing the crush washers from both sides of the fuel line. Then, thread the banjo bolt adapter into the bottom of the fuel filter housing and torque the banjo bolt to 18-20 foot-pounds using a 19mm wrench. Finally, install the fuel pressure sensor into the snubber valve and then into the female end of the banjo bolt adapter.

Frequently asked questions