Changing Fuel Filters: Bobcat 743B Guide For Diy Mechanics

Changing the fuel filter on a 743B Bobcat is a straightforward process, but there are a few things to keep in mind to ensure it's done correctly. Firstly, it's recommended to replace the fuel filter every 1,000 hours or annually, and to always check the water separator bowl, draining it if there is water or a 'water in fuel' code. When replacing the filter, it's important to lubricate the new O-rings and ensure the arrow on the pre-filter is facing the correct direction. Additionally, it's worth noting that some 743B models may have a rubber primer bulb in the fuel line, which can affect fuel flow if it's not functioning properly.

Check and drain water from the water separator bowl

To check and drain water from the water separator bowl of a Bobcat 743B, you should first ensure that you have the necessary equipment. This includes an extra hose, shop towels or rags, and a filter wrench.

Once you have gathered the necessary tools, you can begin the process of checking and draining the water separator bowl. Start by locating the water separator bowl and inspecting it for the presence of water. If water is visible, or if you have received a 'water in fuel' code, you will need to drain the water from the bowl.

To drain the water, attach the extra hose to the drain plug of the water separator bowl. This will allow you to direct the drained water away from the engine and into an appropriate container. Once the hose is securely attached, you can loosen the drain plug using the filter wrench. This will allow the water to drain out of the bowl.

After draining the water, make sure to tighten the drain plug securely to prevent any leaks. It is important to perform this check and drain procedure regularly, especially when you replace the fuel filter or receive a 'water in fuel' code. By keeping the water separator bowl free of water, you can help ensure the proper functioning of your Bobcat 743B's fuel system.

Disconnect the electrical connector and remove the separator bowl

To disconnect the electrical connector and remove the separator bowl, follow these steps:

Firstly, ensure you have the necessary tools and safety precautions in place. Check the water separator bowl and drain it if there is water visible, or if you have been notified by a 'water in fuel' code, or if it is time for a fuel filter replacement. Attach an extra hose and loosen the drain to do this.

Next, disconnect the electrical connector. This will be attached to the separator bowl. Once this is disconnected, carefully remove the separator bowl. It is important to only service this component when required; otherwise, it should be replaced every 1,000 hours or annually.

Now that the separator bowl is removed, you can move on to removing the old filter. This will involve removing the filter and the pre-filter, as well as cleaning the area.

Once the old filter and separator bowl are removed, you can install a new filter. Remember to lubricate the new O-rings and install the separator bowl before attaching the new filter.

Remove the old filter and install a new one

To remove the old filter, first check the water separator bowl. Only drain when water is visible, when notified by the 'water in fuel' code, or at every fuel filter replacement. Install an extra hose and then loosen the drain. Next, disconnect the electrical connector and remove the separator bowl. Finally, remove the filter.

When installing a new filter, do not pre-fill it with fuel. Lubricate the new O-rings and install the separator bowl before placing it onto the filter housing. Connect the electrical components and perform any final cleanup. The fuel system will need to be primed with fuel, and air will need to be removed from the system.

If you are replacing the pre-filter, clean the area and move the hose clamps off. Remove each fuel hose and loosen the filter clamp. Note the orientation of the arrow on the pre-filter before removing and discarding it. Install the new pre-filter with the arrow facing the correct direction. Install the hoses and move the clamps back to the correct position.

Clean the pre-filter and surrounding area

To clean the pre-filter and surrounding area of your Bobcat 743B, you will need shop towels or rags, a filter wrench, and other tools.

First, ensure that the engine is cool before beginning any maintenance work. Check your operation and maintenance manual for reference.

To begin cleaning, move the hose clamps off and remove each fuel hose. Loosen the filter clamp and take note of the orientation of the arrow on the pre-filter before removing and discarding it.

Use your shop towels or rags to clean the surrounding area, ensuring that any dirt or debris is removed.

Once the area is clean, install a new pre-filter with the arrow facing the correct direction. Reinstall the hoses and move the clamps back to their correct positions.

Remember to prime the pre-filter and remove air from the fuel system after installing a new pre-filter.

Remove the old pre-filter and install a new one

To remove the old pre-filter and install a new one on your Bobcat 743B, follow these steps:

First, clean the area around the pre-filter to ensure no dirt or debris can enter the fuel system during the replacement process. Next, locate the fuel hoses connected to the pre-filter and use hose clamps to prevent any fuel spillage. Now, carefully remove each fuel hose by loosening the filter clamp. Note the orientation of the arrow on the pre-filter before removing it; this is important for installing the new pre-filter. Dispose of the old pre-filter safely.

Now it's time to install the new pre-filter. Take the new pre-filter and ensure the arrow is facing the correct direction as indicated by the old pre-filter. Carefully install the new pre-filter into place, making sure it is secure. Reinstall the fuel hoses, ensuring they are securely clamped. Finally, remove the hose pliers and any other tools used during the process.

It is important to prime the new pre-filter and remove any air from the fuel system after installation. Refer to your Bobcat 743B manual for specific instructions on how to do this.

Frequently asked questions