Replacing The Fuel Filter In A '97 Accord: Step-By-Step Guide

Changing the fuel filter on a 97 Honda Accord can be a tricky task. The filter is located on the driver's side of the car, close to the fire wall. While some people have managed to do the whole job from the top, it is generally advised to loosen the lower fuel line from the bottom. To do this, you will need to raise the car and use a long extension, a 14mm crow foot, and a ratchet to loosen the fuel line at the bottom of the filter. Make sure to put a pan under the car to catch any spilling fuel. You will also need a 17mm wrench, a 10mm socket, and possibly a 14mm short line wrench. This process can be time-consuming and challenging, so it may be worth seeking professional help if you are unsure.

The fuel filter is located on the driver's side, close to the firewall

To change the fuel filter on a 1997 Honda Accord, you'll first need to locate the fuel filter. For Accords between 1995 and 2002, the fuel filter is located on the driver's side of the car, close to the firewall.

To access the fuel filter, you'll need to raise the car and work from underneath. Here are the steps to change the fuel filter:

• Remove the gas cap to relieve fuel pressure from the system.
• Loosen the fuel line at the bottom of the filter using a long extension and a 14mm crowfoot wrench. Place a pan under the car to catch any spilled fuel.
• Remove the 17mm nut at the fuel rail and the 17mm bolt for the fuel hose at the fuel filter.
• Undo the lower fuel line from the top (engine compartment).
• Remove the 10mm bolt that holds the fuel filter bracket in place. You may need to play with it a bit to slide it up by the master cylinder.
• Once the bracket is removed, take out the 10mm bolt that holds the filter in the bracket.
• Install the new fuel filter, ensuring it is lined up correctly with the bracket and the body of the car.
• Start the lower fuel line from the top, turning the nut a few times to ensure it is not cross-threaded.
• Mount the bracket back onto the body and tighten the 10mm bolt.
• Tighten the lower fuel line.
• Install the upper hose, ensuring you use new aluminum gaskets.
• Put the gas cap back on.

Once you've completed these steps, start the car and check for any fuel leaks. If there are leaks, turn off the engine and re-tighten the fuel lines.

This process should help you change the fuel filter on your 1997 Honda Accord.

You will need a 14mm crow foot wrench, a long extension, and a ratchet

To change the fuel filter on a 97 Accord, you will need a 14mm crow foot wrench, a long extension, and a ratchet. This is in addition to a 10mm socket, a 17mm wrench, and a new fuel filter and its accompanying washers.

The 14mm crow foot wrench is required to loosen the fuel line at the bottom of the filter. This step is performed from underneath the car, and a pan should be placed under the car to catch any fuel that spills. The long extension and ratchet are used in conjunction with the 14mm crow foot wrench to reach the bottom fuel line.

Once the bottom fuel line is loosened, the next step is to remove the 17mm nut at the fuel rail, which is the top end of the fuel hose going to the filter. Do not lose the aluminum washer, as it needs to be reused. Then, remove the 17mm bolt for the fuel hose at the fuel filter and remove the hose.

At this point, you can completely undo the lower fuel line, but it is recommended to do this from the top of the engine compartment. Next, remove the 10mm bolt that holds the fuel filter bracket, and remove the assembly. The fuel filter and bracket assembly can be tricky to remove and may require some maneuvering. Once the assembly is out, remove the 10mm bolt that holds the filter in the bracket, and install the new filter, ensuring it is lined up correctly.

Before reinstalling the bracket, check that the lower bracket nipple is installed inside the opening in the body where the filter bracket mounts. Start the lower fuel line from the top, ensuring it is not cross-threaded, and then mount the bracket to the body and tighten the 10mm bolt. Tighten the lower fuel line and install the upper hose, using new aluminum gaskets. Finally, put the gas cap back on and start the car to check for any fuel leaks.

You may need to remove the brake master cylinder to access the fuel filter

To access the fuel filter on a 1997 Honda Accord, you may need to remove the brake master cylinder. This is because the fuel filter is located under the hood, on the driver's side, below the brake master cylinder.

Step 1: Prepare the necessary tools and parts

You will need the following tools: a 10mm socket, a 17mm socket, a 17mm wrench, a 3/8 drive short and long extension, a ratchet, a 3/8 drive 14mm crow foot, and a 14mm short line wrench. For parts, you will need a new fuel filter (part # 16010-st5-933) and new aluminum washers.

Step 2: Relieve fuel line pressure

Start by removing the gas cap. This will relieve the pressure in the fuel line, making it safer to work on.

Step 3: Loosen the fuel line

Raise the car and use the long extension and 14mm crow foot to loosen the fuel line at the bottom of the filter. Do not completely undo the line yet, as fuel will spill out. Place a pan under the car to catch any fuel.

Step 4: Remove the fuel hose and bracket

Remove the 17mm nut at the fuel rail (the top end of the fuel hose going to the filter). Be careful not to lose the aluminum washer, as you will need to reuse it. Also, remove the 17mm bolt for the fuel hose at the fuel filter and then remove the hose itself. Now, undo the lower fuel line from the top (engine compartment). Remove the 10mm bolt that holds the fuel filter bracket, and remove the assembly. This may require some wiggling, but it will slide up by the master cylinder.

Step 5: Remove the old fuel filter

Once the assembly is out, remove the 10mm bolt that holds the filter in the bracket. Be prepared for some fuel spillage during this step.

Step 6: Install the new fuel filter

Install the new fuel filter, making sure to line it up with the slot. If you look at the body where the filter bracket mounts, you will see an opening below the mounting bolt. Make sure to install the lower bracket nipple inside that hole.

Step 7: Reinstall the fuel line and bracket

Before installing the 10mm bracket bolt, start the lower fuel line from the top. Turn the nut a few times to ensure it is not cross-threaded. Once the line is started, mount the bracket on the body and tighten the bolt. Then, tighten the lower fuel line and install the upper hose, using new aluminum gaskets.

Step 8: Reassemble and check for leaks

Finally, reinstall the gas cap and start the car. Check for any fuel leaks. Reconnect all the components that were removed or disconnected during the process, such as the emission box plugs and vacuum hoses.

The fuel filter bracket can be tricky to remove and reinstall

The fuel filter bracket on a 1997 Honda Accord can be tricky to remove and reinstall. Here are some detailed instructions to help you with the process:

Firstly, locate the fuel filter. It is on the driver's side of the car, close to the firewall. You can find it by following the hose that goes down from the fuel rail. Once you have located the fuel filter, gather the necessary tools, including a 14mm crow foot, a long extension, a ratchet, and a 10mm bolt.

To remove the fuel filter bracket, start by raising the car. Loosen the bottom line of the fuel filter using the crow foot and long extension. You may need to lift the car up and down a few times to access the bolts properly. Be careful, as some fuel will spill when you loosen the line. Next, lower the car and remove the 17mm banjo bolt at the top of the fuel filter. Now, undo the lower line from the top. Again, be cautious as fuel may spill.

At this point, you can remove the 10mm bolt that attaches the fuel filter bracket to the firewall. The bracket and filter assembly can then be removed. It may be a tight fit, but it will come out. Once removed, you can replace the fuel filter. Make sure to orient it correctly and tighten the filter bracket before reinstalling the fuel lines.

When reinstalling the fuel lines, use new sealing washers that come with the new fuel filter. Reinstall the lines with the banjo bolts and new washers. Cycle the ignition key from "Off" to "On" a few times to repressurize the fuel system. Finally, start the engine and check for any leaks. If there are no leaks, you have successfully replaced the fuel filter and bracket.

This process can be tricky, and it may be helpful to have a second person assisting you. Take your time and be cautious when handling fuel to avoid any spills or accidents.

Make sure to use new aluminium washers when reinstalling the fuel filter

When reinstalling the fuel filter, it is important to use new aluminium washers. The fuel filter on a 1997 Honda Accord is located on the driver's side of the car, close to the fire wall. It is a tricky process to replace the fuel filter, and it is recommended to have two people working together. One person should be under the car with crow foot wrenches and extensions to get to the fuel line bolt, while the other person is in the engine compartment.

First, relieve the fuel line pressure by removing the gas cap. Then, loosen the bottom fuel line, but do not completely undo it, as fuel will spill out. Place a pan under the car to catch any fuel that does escape. Remove the nut at the fuel rail and the bolt for the fuel hose at the fuel filter, then remove the hose. Now, undo the lower fuel line from the top.

Next, remove the bolt that holds the fuel filter bracket, and remove the assembly. Take out the bolt that holds the filter in the bracket, and install the new filter, ensuring it is lined up correctly. Before installing the bracket bolt, start the lower fuel line from the top, ensuring it is not cross-threaded. Mount the bracket and tighten the bolt, then tighten the lower fuel line. Install the upper hose, ensuring new aluminium washers are used.

Finally, replace the gas cap and start the car, checking for any fuel leaks.

Frequently asked questions