Replacing Fuel Filter In '09 Cobalt: Step-By-Step Guide

If you're looking to replace the fuel filter on your 2009 Chevy Cobalt, this is the guide for you. The fuel filter is located in the rear of the car, near the fuel tank, between the back wheels. You'll need to lift your car with a jack to access it. Before you start, make sure you have the right tools, including a 10mm ratchet/wrench and a 3/8 fuel line disconnect tool. First, depressurize the fuel system by removing the fuel pump relay from the fuse box and starting the car. The car will then turn off. Next, remove the fuel lines and bolt from the fuel filter. Take out the old filter and replace it with a new one, securing it with the bolt and fuel lines. Repressurize the fuel system by turning the key to the ON position and checking for leaks. Finally, you're ready to start the car and drive!

Depressurise the fuel system

Depressurising the fuel system of a Chevy Cobalt is a crucial step when changing the fuel filter. Here is a detailed, step-by-step guide on how to do it:

• Depressurise the Fuel System: Start by locating the fuse box and removing the fuel pump relay. Then, turn the ignition key to start the car. The car will struggle and eventually die. At this point, turn off the car and replace the relay. This process releases the pressure in the fuel system, making it safe to work on.
• Locate the Fuel Filter: Move to the rear of the car, and find the fuel filter near the fuel tank, between the back wheels. You may need to jack up the car to access this area comfortably.
• Remove the Fuel Lines: Before removing the fuel lines, it is recommended to unclamp and move the wires circled in blue (as shown in the diagram) for easier access. Then, remove the two fuel lines circled in red using your hands or a suitable tool. Finally, disconnect the fuel line circled in green using a fuel line quick-disconnect tool.
• Final Steps Before Removal: At this stage, you will only have one bolt holding the fuel filter in place (circled in yellow). Remove this bolt, and the fuel filter can be taken out. Now, you can proceed to install the new fuel filter by reversing the above steps.

Remember to put safety first when working on your car. Always secure the vehicle properly, wear gloves and safety glasses, and refer to the owner's manual for additional instructions or warnings.

Locate the fuel filter

To locate the fuel filter of a Chevy Cobalt, you will need to lift the right back side of the car using a jack. Once you have done this, you should be able to see the fuel filter, which is located in the rear of the car, near the fuel tank, between the back wheels.

Some Chevy Cobalt models have the fuel filter integrated into the fuel pump assembly, meaning it is inside the tank. If this is the case, you will need to remove the fuel tank to access the fuel filter.

Remove the fuel lines

To remove the fuel lines from your 2009 Cobalt, you will need a jack to lift the rear of your car, a 10mm wrench, and a fuel line disconnect tool.

First, depressurise the fuel system. Do this by removing the fuel pump relay from the fuse box and starting the car. The car will splutter and die. Turn the car off and replace the relay.

Next, locate the fuel filter at the rear of the car, near the fuel tank, between the back wheels. You will need to lift the car to access this area.

Now, remove the two fuel lines circled in red in the image below. It is easier to access these lines if you first unclamp and move the wires circled in blue.

! [Fuel Filter Removal](https://i.imgur.com/mJeZ5nF.png)

Then, remove the fuel line circled in green using your fuel line disconnect tool. Finally, remove the bolt circled in yellow, and the fuel filter will come out.

Be sure to take appropriate safety precautions when performing this task, including carefully securing the vehicle on the jack and wearing gloves and safety glasses.

Remove the bolt and the fuel filter

To remove the bolt and the fuel filter, follow these steps:

First, locate the bolt and the fuel filter. The fuel filter is located at the rear of the car, near the fuel tank, between the back wheels. You will need to lift your car using a jack on the right back side of the car. Once you have located the fuel filter, you will see a bolt attaching it to the body of the car.

Second, gather the right tools. You will need a 10mm wrench to remove the bolt. You will also need a fuel line disconnect tool to remove the fuel lines.

Third, remove the bolt. Using the 10mm wrench, loosen and remove the bolt that holds the fuel filter in place.

Fourth, remove the fuel lines. There are two fuel lines connected to the fuel filter. Use the fuel line disconnect tool to disconnect them. Be careful not to damage the fuel lines, as this could cause a leak.

Fifth, remove the fuel filter. With the bolt and fuel lines removed, you can now take out the old fuel filter. Be careful not to drop it or cause any spills. Place it in a safe container for proper disposal.

By following these steps, you will be able to successfully remove the bolt and the fuel filter on your 2009 Chevy Cobalt. Remember to refer to your owner's manual for additional information and safety precautions before beginning any maintenance work.

Repressurise the fuel system

To repressurise the fuel system of a 2007 Chevrolet Cobalt, follow these steps:

Place the key in the ignition and turn it to the "ON" position. You should hear the fuel pump making a whirring sound. Check the fuel lines at the fuel filter for any leaks. Turn the key back to "OFF" and wait 10 seconds. Then turn the key to the "ON" position again, wait for the fuel pump to finish pressurising, and you are ready to start the car. Check for leaks one last time, then you are ready to drive.

This is the final step in changing the fuel filter of a 2007 Chevrolet Cobalt. The first step is to depressurise the fuel system by pulling the fuel pump relay out of the fuse box and starting the car. The car will then stumble and die. You can then turn off the car and replace the relay. Next, go to the rear of the car and find the fuel filter. Remove the fuel lines and the bolt holding the fuel filter in place, and remove the old filter. Insert the new fuel filter and install back the pipelines and bolt.

Frequently asked questions