Replacing Fuel Strainer In Jeep Grand Cherokee (2007 Model)

If you're looking to change the fuel strainer in your 2007 Jeep Grand Cherokee, you've come to the right place. This guide will take you through the process step-by-step, ensuring you have all the information you need to complete the task safely and efficiently. By following these instructions, you'll be able to replace the fuel strainer and get your Jeep back on the road in no time.

Removing the rear bumper, hitch and skid plate

To access the fuel filter of a 1999-2004 Jeep Grand Cherokee, you'll need to remove the rear bumper, hitch, and skid plate. Here's a step-by-step guide on how to do it:

First, it's recommended to have the rear of your car raised as high as possible on jack stands. This will give you better access to the undercarriage. Once your car is securely raised, locate the fuel tank and position a floor jack underneath it. You may need to remove some bolts from the front of the skid plate to access the tank.

With the floor jack in place, carefully lower the fuel tank. Tilt it downwards, as this will make it easier to access the fuel pump. At this point, you may also notice some bolts that need to be removed to fully detach the tank.

With the fuel tank lowered and tilted, you should now have clear access to the fuel pump and the surrounding components, including the hitch and skid plate. Carefully remove any remaining bolts or fasteners that are holding these components in place. Make sure to keep track of the bolts and their locations, as you'll need to reinstall them later.

Once all the bolts are removed, carefully detach the rear bumper, hitch, and skid plate assembly from the vehicle. Set it aside in a safe place, as you'll need to reinstall it later.

Now that you've removed the rear bumper, hitch, and skid plate, you should have clear access to the fuel pump and fuel filter. Remember to work carefully, as the fuel system is under constant pressure, even with the engine off. Always perform a fuel system pressure release procedure before beginning any work.

Jacking up the car

Park Your Car on a Level Surface

Before you begin, ensure your Jeep is parked on a flat, level surface, such as a driveway or a flat stretch of road. This is important for stability and safety when jacking up the car. Engage the parking brake to prevent accidental movement.

Prepare the Necessary Tools and Safety Equipment

You will need a floor jack, jack stands, and wheel chocks (or similar objects to block the wheels). It is also recommended to wear safety gear, including gloves and eye protection, to prevent injuries.

Secure the Wheels and Place the Jack

Place the wheel chocks or similar objects in front of the front wheels and behind the rear wheels to prevent accidental rolling. Position the floor jack at the recommended lift point of your Jeep Grand Cherokee, which is typically under the frame near the front or rear wheels. Refer to your owner's manual for the exact jacking points.

Lift the Vehicle

Slowly raise the jack until it makes contact with the frame of the car. Continue lifting until the car is high enough to provide ample clearance for you to work comfortably. Ensure that the jack is stable and secure.

Position the Jack Stands

Place the jack stands at the recommended points under the vehicle's frame, close to the jacking point. Carefully transfer the weight of the car from the jack to the stands. Lower the jack slightly until it is no longer supporting the weight, and confirm that the vehicle is securely held by the jack stands.

Double-Check Stability

Before proceeding with any repairs or maintenance, ensure that the vehicle is stable and secure on the jack stands. Give the car a gentle shake to confirm that it won't move or shift unexpectedly.

Remember to follow all safety precautions when working under a lifted vehicle. Always use jack stands and never rely solely on a jack to support the weight of the car. Do not work under a lifted car without proper support and safety measures in place.

Draining the fuel tank

To drain the fuel tank of a 1999-2004 Jeep Grand Cherokee, follow these steps:

First, perform the Fuel System Pressure Release Procedure. This is important as the fuel system is under constant pressure, even when the engine is off. Next, drain the fuel tank and remove the tank. You will need to wash and clean the area around the pump module to prevent contaminants from entering the tank.

Now, disconnect the fuel return and pressure lines from the fuel pump module fittings. You can then remove the module from the fuel tank.

It is important to note that the fuel tank removal is necessary for the fuel pump module removal. Also, whenever the fuel pump module is serviced, the module gasket must be replaced.

Disconnecting fuel return and pressure lines

Disconnecting the fuel return and pressure lines is a crucial step when changing the fuel strainer on a 1999-2004 Jeep Grand Cherokee. Here is a detailed guide on how to perform this task:

Firstly, it is important to note that the fuel system is under constant pressure, even when the engine is turned off. Therefore, before beginning any work on the fuel pump module, the fuel system pressure must be released. This is done by performing the Fuel System Pressure Release Procedure.

Once the pressure has been released, the next step is to drain the fuel tank and remove it. Refer to your Jeep Grand Cherokee's manual for the correct procedure to drain and remove the fuel tank. After removing the fuel tank, the area around the pump module should be thoroughly washed and cleaned to prevent contaminants from entering the tank.

Now, you are ready to disconnect the fuel return and pressure lines. These lines are connected to the fuel pump module fittings. To disconnect them, refer to the Quick-Connect Fittings guide or manual for the correct procedure. It is important to be cautious during this step to avoid any spills or leaks.

After disconnecting the fuel return and pressure lines, you can proceed to the next step, which involves removing the plastic fuel pump module locknut. This locknut is threaded onto the fuel tank, and you will need Special Tool 6856 to remove it. Once the locknut is removed, the fuel pump module will spring up slightly.

By following these steps, you will have successfully disconnected the fuel return and pressure lines, allowing you to access and replace the fuel strainer on your 1999-2004 Jeep Grand Cherokee. Remember to exercise caution when working with the fuel system and always refer to the appropriate manuals or guides for specific instructions for your vehicle.

Removing the fuel pump module locknut

To remove the fuel pump module locknut from a 1999-2004 Jeep Grand Cherokee, follow these steps:

Firstly, perform the Fuel System Pressure Release Procedure. Then, drain the fuel tank and remove it. You will need to wash and clean the area around the pump module to prevent contaminants from entering the tank. Disconnect the fuel return and pressure lines from the fuel pump module fittings.

The next step is to remove the locknut. The plastic fuel pump module locknut is threaded onto the fuel tank. Install Special Tool 6856 to the fuel pump module locknut and remove it. The fuel pump module will spring up slightly after the locknut is removed.

Now, you can remove the module from the fuel tank. It is important to note that whenever the fuel pump module is serviced, the module gasket must be replaced.

Frequently asked questions