Replacing The Fuel Line Filter On A Homelite Blower

If you're looking to change the fuel line filter on your Homelite Blower UT08934, you've come to the right place. This repair guide will walk you through the process step-by-step, ensuring you can get your blower up and running again in no time. It's important to note that fuel lines can clog, crimp, or crack, restricting gas flow and preventing the engine from starting. So, if you're experiencing any of these issues, it's definitely time for a change.

Remove the fuel tank

To remove the fuel tank from a Homelite Blower UT08934, you will need to purchase a replacement fuel tank assembly, as the fuel tank does not appear to be sold separately. The fuel tank assembly is part number 308123004. You can purchase this from Amazon or RepairClinic.com.

Before installing the new fuel tank, drain the gas tank into an approved storage container in a well-ventilated area. Wear work gloves to protect your hands.

To remove the old fuel tank, first wipe around the fuel cap to prevent any dirt from falling into the fuel tank when removing it. Then, take off the fuel cap and, using a clean, bent wire, hook the fuel line and pull the fuel filter out of the tank. With one hand securely holding the fuel line, pull the filter out of the line with the other hand.

You can then dispose of the old fuel tank and install the new fuel tank assembly, ensuring that you follow the instructions provided with the product.

Remove the carburetor

To remove the carburetor from your Homelite blower UT08934, you will first need to locate the carburetor itself. It is found just below the air filter and has three adjustment screws on its side.

Once you have located the carburetor, you will need to remove the air filter and any other components that may be blocking access to the carburetor. This may include the fuel tank, which is available as a replacement part. Be sure to also order a fuel tank with lines and a fuel filter if you need to replace this component.

Next, you will need to disconnect the carburetor from the engine. This will involve detaching any hoses, tubes, or wires connected to it. Be careful not to damage these parts, as they are essential for the proper functioning of your blower.

Once the carburetor is disconnected, you should be able to remove it from the blower. Be sure to handle it with care, as it is a delicate component.

If you are replacing the carburetor, be sure to purchase a genuine Homelite replacement part to ensure compatibility and proper functioning. You can find replacement parts on websites such as eReplacementParts.com and RepairClinic.com.

Additionally, if you are having issues with your carburetor, you may want to try adjusting it before removing it entirely. This can be done by adjusting the "H" (high throttle), "L" (low speed), and "C" (idle) screws on the side of the carburetor with a screwdriver.

Remove the blower tube

To remove the blower tube from your Homelite UT08934 blower, follow these steps:

• Park the blower on a flat, level surface and ensure the engine is turned off.
• Locate the blower tube at the front of the blower.
• Using a pair of gloves to protect your hands, firmly grip the blower tube and twist it in a counter-clockwise direction to loosen it.
• Once the tube is loosened, carefully pull it away from the blower to remove it completely.

• If the blower tube is difficult to remove, you can use a pair of pliers to get a better grip and apply more force.
• Be gentle when removing the tube to avoid damaging any nearby components or the tube itself.
• It is recommended to clean the blower tube and the area where it connects to the blower while you have it disassembled. This will help ensure that your blower continues to function optimally.
• Before reassembling the blower tube, inspect it for any signs of damage or wear. Replace the tube if necessary.

Remove the air filter cover

To remove the air filter cover from your Homelite leaf blower, start by making sure the engine has cooled down. Then, remove the wire and boot from the spark plug to prevent the engine from accidentally starting. If it's still intact, lift the tab to detach the old air filter cover.

Before installing the new air filter cover, make sure the gasket is properly positioned on the filter base, then align the new cover and snap it into place. Finally, reattach the wire and boot to the spark plug.

Pull out the fuel lines from the tank

To pull out the fuel lines from the tank of your Homelite blower UT08934, you will first need to remove the fuel tank from the housing.

Removing the fuel tank from the housing

• Remove the screws from the front of the muffler guard cover and pull the guard cover off the muffler.
• Remove the blower tube thumb screw from the front of the housing.
• Remove the screws from the right side of the housing and pull the left side of the housing off the blower. The fan cover and handle come off with the housing.
• Remove the fuel tank from the housing.

Pulling out the fuel lines from the tank

• The end of the small fuel line is connected to the fuel filter inside the tank. Use needle-nose pliers to fish the fuel filter out of the mouth of the tank.
• Remove the fuel filter from the end of the small fuel line.
• Pull the small fuel line out of the tank through the mounting hole.
• Push the large fuel line into the tank through the mounting hole and pull it out of the mouth of the tank.

Frequently asked questions