Changing The Fuel Filter On A 455 Rancher: Step-By-Step Guide

The fuel filter on a Husqvarna 455 Rancher chainsaw is connected to the fuel line inside the gas tank and blocks dirt, oil, and woodchips from getting into the fuel line. To replace the fuel filter, you will need to empty the gas tank, disconnect the fuel line from the carburetor, and use pliers to pull out the old fuel filter. You can then attach the new fuel filter to the fuel line and push it back into the gas tank.

How to change fuel filter on 455 Rancher

Empty the gas tank and run the engine until it cuts out

To change the fuel filter on your Husqvarna 455 Rancher, you'll first need to empty the gas tank. This is an important safety precaution as it will reduce the risk of spills and limit the amount of gasoline you are exposed to. Once the tank is empty, start the engine and let it run until it cuts out. This will burn through any remaining fuel in the lines, ensuring that the fuel filter is completely drained.

At this point, your chainsaw will be powered only by whatever fuel remains in the lines and the carburetor. It is important to work efficiently from this point on to avoid damaging your engine by running it without fuel.

With the engine off, you can now begin to disconnect the fuel line from the carburetor, which is located at the rear of the saw, near the throttle. Depending on your model, you may need to remove the air filter to access this area. However, you should not need to disassemble the throttle.

Now, use a pair of pliers to pull the old fuel filter further into the gas tank. This will give you access to the fuel line, which is connected to the filter. Pull out enough of the line so that you can remove the old fuel filter from the tank. Be careful not to damage the fuel line as you do this.

Once the old fuel filter is out, you can dispose of it appropriately. Then, take the new fuel filter and attach it to the fuel line. Use the pliers to push the new filter and the fuel line back into the gas tank.

Disconnect the fuel line from the carburetor

To disconnect the fuel line from the carburetor of your Husqvarna 455 Rancher, you will need to first loosen the hose from the carburetor. This will allow you to then pull the hose up through the tank.

It is important to note that you should not use fluted pliers with the fuel hose as they can cause material damage, resulting in damage to the fuel hose. Instead, you should use a special tool, such as the 502 50 83-01, to perform this task. This tool is designed to be inserted into the hose bushing at the bottom of the carburetor suspension and out through the tank opening.

Once you have loosened the hose and inserted the tool, you can then secure the hose onto the end of the tool and pull it through the hose bushing. This will give you access to the fuel line and carburetor connection, allowing you to disconnect the fuel line.

Now that the fuel line is disconnected from the carburetor, you can proceed with replacing or repairing the fuel filter as needed. Remember to exercise caution when working with gasoline and other flammable materials.

Remove the old fuel filter

To remove the old fuel filter from your Husqvarna 455 Rancher, you will need to take the following steps:

Firstly, ensure that the gas tank is empty. Start the chainsaw and let it run until the engine stops. This will ensure that the tank is empty and that there is no more fuel going into the engine.

Next, disconnect the fuel line from the carburetor, which is located at the rear of the chainsaw, near the throttle. Depending on your model, you may need to remove the air filter to access this. However, you should not need to disassemble the throttle.

Now, pull the fuel line further into the gas tank using pliers. Pull it out enough so that the old fuel filter comes out of the tank. Once you have pulled out the fuel line, take the old fuel filter off by hand. It may require a few firm tugs to remove it completely. Dispose of the old fuel filter responsibly.

At this point, you have successfully removed the old fuel filter. The next step would be to install the new fuel filter and reassemble the fuel line and carburetor.

Install the new fuel filter

To install the new fuel filter on your 455 Rancher, start by fitting the new fuel filter onto the fuel line. You can do this by placing the new fuel filter onto the fuel line and twisting it in place. Make sure you don't use fluted pliers for this step, as they can cause material damage to the fuel hose. Push the fuel filter back into the gas tank.

Next, use pliers to feed the fuel line back through its casing. You may need to wiggle the line back and forth to get it to slide all the way in. Pull out the exposed fuel line from the rear of the saw using the pliers. Now, reattach the fuel line to the carburetor.

Finally, secure the gas cap back on the saw and you're done! Remember always to exercise caution when working with gasoline and other flammable materials.

Reattach the fuel line to the carburetor

To reattach the fuel line to the carburetor of your Husqvarna 455 Rancher, you will need to follow a few steps. It is important to note that you should use caution when working with gasoline and other flammable materials.

First, loosen the hose from the carburetor. Pull the hose up through the tank. You can use a tool, such as a pair of pliers, to help you with this step. Insert the tool into the hose bushing at the bottom of the carburetor suspension and out through the tank opening.

Next, secure the new hose onto the end of the tool. Pull the hose through the hose bushing using the tool. Once the hose is through, cut off both ends of the hose. Now you can fasten the hose to the carburetor and fuel filter.

Make sure that you do not use fluted pliers with the fuel hose, as they can cause material damage and lead to further issues.

Frequently asked questions