Changing Fuel Filters: 1999 Mazda Millenia Guide

The fuel filter in a 1999 Mazda Millenia requires a unique replacement process compared to other Mazda vehicles. This guide will outline the steps to safely replace the fuel filter in your car. It is important to note that fuel filters should be replaced every 20,000 to 50,000 miles as part of routine maintenance.

Park the car and relieve fuel pressure

To relieve fuel pressure on your 1999 Mazda Millenia, start by parking the car on a level surface in a well-ventilated area. This is important for safety, as you will be working with gasoline, which can be dangerous.

Next, turn off the ignition and remove the fuel cap from the fuel tank. Unscrewing the fuel cap will help to relieve pressure from the fuel filter. Now, open the trunk and remove the trunk mat or carpet liner to access the service hole cover.

At this point, you should disconnect the negative battery cable. This will ensure that there is no power going to the fuel system, reducing the risk of accidental ignition.

With the ignition off, the fuel cap removed, and the battery disconnected, you have successfully relieved the fuel pressure in your 1999 Mazda Millenia. You can now proceed with the rest of the fuel filter replacement procedure, which includes disconnecting and plugging the fuel lines, removing and replacing the fuel filter, and then reassembling the components in the reverse order.

Remember to work in a well-ventilated area, wear protective gear, and avoid any open flames or sparks during the procedure.

Remove the trunk mat and spare tire

To remove the trunk mat and spare tire from your 1999 Mazda Millenia, follow these steps:

Begin by parking your car on a level surface in a well-ventilated area. Ensure that the ignition is turned off.

Open the trunk of your Mazda Millenia. You will now need to remove the trunk mat and spare tire. First, pull back the carpet cover from the rear of the trunk. Then, remove the spare tire and set it aside, outside of the car.

Now, locate the metal cover at the very rear of the trunk. This cover is held in place by three nuts, which you will need to remove using a 3/8-inch drive ratchet and a 10 mm socket. Once the nuts are removed, pull out the cover and place it outside the trunk, giving you access to the fuel filter.

At this point, you can proceed to disconnect the fuel lines and remove the old fuel filter, following the steps outlined in the fuel filter replacement guide. Remember to place a small fluid catch pan underneath to catch any fuel that may leak out during the process.

Remove the metal cover

To remove the metal cover, you will need a 3/8-inch drive ratchet and a 10 mm socket. First, locate the metal cover at the very rear of the trunk. You will see that there are three nuts holding it in place. Use the 3/8-inch drive ratchet and 10 mm socket to remove these three nuts. Once the nuts have been removed, you can pull the cover out and place it outside of the trunk. Now, you will be able to access the fuel filter.

It is important to ensure that you have parked your Mazda Millenia on a level surface in a well-ventilated area before beginning this process. Additionally, always make sure to wear protective glasses when working around gas.

Disconnect and remove the fuel filter

To disconnect and remove the fuel filter of a 1999 Mazda Millenia, follow these steps:

Firstly, park your car on a level surface in a well-ventilated area. This is important for safety, as you will be working with fuel. Unscrew the fuel cap from the fuel tank to relieve pressure from the fuel filter. Open the trunk and remove the trunk mat and spare tire.

Now, locate the metal cover at the rear of the trunk. This is held in place by three nuts, which you will need to remove with a 3/8-inch drive ratchet and a 10 mm socket. With the cover removed, you will be able to access the fuel filter. Place a small fluid catch pan underneath the fuel filter to catch any spills.

At this point, you can disconnect the fuel lines from the fuel filter. Grasp the end of the fuel lines with pliers and rotate the fuel line back and forth while pulling out, repeating this process until the fuel line slides off the fuel filter stop. Do this for both rubber fuel lines. Ensure you plug the lines to prevent leakage.

Now that the fuel lines are disconnected, you can remove the nut from the fuel filter bracket and remove the filter and bracket from the vehicle. Finally, remove the filter from the mounting bracket.

To install the new fuel filter, simply follow these steps in reverse. Position the new filter in the mounting bracket, then install and tighten the bracket nut. Reconnect the fuel lines, ensuring they are secure. Reinstall the metal cover and tighten the bolts.

Now, you can replace the trunk mat and spare tire, close the trunk, and screw the gas cap back on. Reconnect the negative battery cable and turn the ignition on and off three times to fill the new fuel filter with gas. Crank the engine on the fourth turn and let it run for about a minute before turning it off.

Always take great care when working with fuel. Ensure you wear protective eyewear and never smoke or have open flames nearby.

Install the new fuel filter

To install the new fuel filter, first position the new fuel filter where the old fuel filter was, with the arrow on the side of the new fuel filter facing towards the engine. Then, push the rubber fuel lines straight onto the fuel filter ports until the fuel lines make it over the fuel line stops on the fuel filter ports. You may have to use pliers to pull the fuel lines over the fuel line stops. Do this to both sides of the fuel filter.

Next, put the metal cover back over the fuel filter and screw the three 10 mm bolts back into the cover. Tighten the bolts down with a 3/8-inch drive ratchet and a 10 mm socket. Remove the small fluid container.

Put the spare tire back into place in the trunk. Then, place the carpet properly in place inside the trunk and close the trunk. Screw the gas cap back onto the fuel tank. Make sure that the gas cap is screwed on completely until you can hear it click. This will prevent air from entering the gas tank.

Frequently asked questions