Replacing Fuel Filter: 1999 Dodge Ram Step-By-Step Guide

Changing the fuel filter on a 1999 Dodge Ram is a complex process that requires specific tools and safety precautions. The fuel filter is responsible for trapping sediments in the gas before it reaches the fuel injectors and engine. While the process is similar to changing the fuel filter on other Dodge Ram models, there are some unique differences. This guide will outline the steps to safely change the fuel filter on a 1999 Dodge Ram.

The fuel filter is in the fuel tank

To change the fuel filter on a 1999 Dodge Ram, you'll first need to locate the fuel filter. In this model of Dodge Ram, the fuel filter is located inside the fuel tank.

Park Your Vehicle and Open the Hood

To begin, park your 1999 Dodge Ram 1500 in a level working area and open the hood.

Locate the Fuel Filter

The fuel filter is mounted near the rear of the driver's side of the firewall. It's housed within a black canister with a drain handle and a small rubber tube attached. Place a catch pan under the rubber tube.

Drain the Fuel Filter Housing

Turn the drain handle to drain the gas from the fuel filter housing into the catch pan.

Remove the Fuel Filter Housing Lid

Use a ratchet and socket to remove the lid from the fuel filter housing. Turn the lid counterclockwise to loosen and remove it.

Discard the Old Fuel Filter

Pull out the old fuel filter from the housing and discard it into the catch pan.

Insert the New Fuel Filter

Slide the new fuel filter into the housing. Also, replace the canister lid O-ring with the new one that comes with the new fuel filter.

Reinstall the Fuel Filter Housing Lid

Put the lid back onto the fuel filter housing and tighten it down with the ratchet and socket.

Prime the Fuel System

Turn the ignition key on and off four times to prime the canister with fuel. Crank the engine on the fourth turn of the ignition and let it run for about 30 seconds before turning it off.

Inspect for Leaks

Finally, inspect the fuel filter housing lid for any leaks and close the hood.

Remember to dispose of the used fuel filter properly, according to your local and state laws. Do not smoke, and always wear safety glasses when working with fuel.

How to drain the gas from the fuel-filter housing

To drain the gas from the fuel-filter housing of a 1999 Dodge Ram, follow these steps:

Park your Dodge Ram in a level working area and open the hood. Locate the fuel filter, which is a black canister housing mounted near the rear of the driver's side of the firewall. You will see a drain handle attached to the fuel filter housing with a small rubber tube. Place a catch pan under this tube.

To drain the gas, simply turn the handle. Once the gas has been drained, you can proceed to remove the lid to the fuel-filter housing with a ratchet and socket. Turn the lid counterclockwise to loosen and remove it. Pull out the old fuel filter and discard it into the catch pan.

Now, you can install a new fuel filter. Slide it into the housing and replace the canister lid O-ring with the new O-ring that comes with the new fuel filter. Put the lid back on and tighten it down with the ratchet and socket.

Finally, remove the fluid catch pan from the engine compartment. Turn the ignition key on and off four times to prime the canister with fuel, then crank the engine on the fourth turn. Let the engine run for about 30 seconds, then turn it off. Check the fuel-filter housing lid for leaks and close the hood.

Removing the fuel filter from the housing

To remove the fuel filter from the housing of your 1999 Dodge Ram, follow these steps:

Firstly, park your Dodge Ram in a level working area and open the hood. Locate the fuel filter, which is a black canister housing mounted near the rear of the driver's side of the firewall. You will see a drain handle attached near the fuel filter housing with a small rubber tube. Place a catch pan under this tube and turn the handle to drain the gas from the fuel filter housing.

Now, to remove the fuel filter from its housing, you will need to remove the lid of the housing. Use a ratchet and socket to turn the lid counterclockwise and loosen it. Once loosened, simply remove the lid and take out the old fuel filter. Be sure to discard it into the catch pan.

At this point, the fuel filter should be easily removable from its housing. Take the new fuel filter and slide it into the housing. It is important to also replace the canister lid O-ring with the new O-ring that comes with the new fuel filter.

Finally, put the lid back onto the fuel filter housing and tighten it down with the ratchet and socket.

Please note that these instructions are for the 1999 Dodge Ram 1500 model and may not apply to other models or years. Always take the necessary safety precautions when working with fuel and ensure you are in a well-ventilated area.

Replacing the fuel filter and O-ring

To replace the fuel filter and O-ring on a 1999 Dodge Ram, follow these steps:

Park your Dodge Ram in a level working area and open the hood. The fuel filter is located near the rear of the driver's side of the firewall. It is a black canister housing that holds the fuel filter inside.

Place a catch pan under the drain handle attached to the fuel filter housing. There will be a small rubber tube connected to the drain handle. Turn the handle to drain the gas from the fuel filter housing into the catch pan.

Using a ratchet and socket, remove the lid of the fuel filter housing by turning it counterclockwise. Pull out the old fuel filter from the housing and discard it into the catch pan.

Slide the new fuel filter into the housing. Replace the canister lid O-ring with the new O-ring provided with the new fuel filter. Ensure the O-ring is properly seated and lubricated to prevent leaks.

Put the lid back onto the fuel filter housing and tighten it down with the ratchet and socket. Remove the fluid catch pan from under the vehicle.

Turn the ignition key on and off four times to prime the canister with fuel. Crank the engine on the fourth turn of the ignition and let it run for about 30 seconds before turning it off.

Inspect the fuel filter housing lid for any leaks. Ensure that the new O-ring is properly seated and there are no signs of fuel leakage. Close the hood when you're done.

Always dispose of used fuel filters properly. Most quick-lube shops will accept used fuel filters for disposal. Never smoke near gasoline, and always wear safety glasses when working with fuel.

Re-attaching the fuel-filter housing

Firstly, ensure that the new fuel filter is correctly seated inside the housing. Then, take the new O-ring that came with the new fuel filter and fit it into the canister lid. Place the lid back onto the fuel-filter housing, ensuring it is properly aligned. Tighten the lid using a ratchet and socket. Be careful not to over-tighten, as this could damage the O-ring and cause leaks.

Once the lid is secure, remove the fluid catch pan from the engine compartment. At this point, you are ready to crank the engine. Turn the ignition key on and off four times to prime the canister with fuel. Then, on the fourth turn of the ignition, crank the engine. Let the engine run for approximately 30 seconds, and then turn it off.

Finally, inspect the fuel-filter housing lid for any signs of leaks. If no leaks are detected, close the hood. Your new fuel filter is now installed, and you can dispose of the old filter and fluid catch pan according to your local and state laws.

Frequently asked questions