Changing The Fuel Filter In Peugeot 206: Step-By-Step Guide

Changing the fuel filter on a Peugeot 206 depends on the model of the car. For example, for the Peugeot 206 CC 2D, you will need to unscrew the fuel filler cap, lift the car using a jack, prepare a container for fluids, clean the fasteners of the fuel supply lines, and then remove the fuel lines from the car body. However, for the Peugeot 206 1.4 LX 2002, the fuel filter is located under the bonnet, under the engine cover if fitted, and is located in a plastic housing.

Jack up the car or place it over an inspection pit

Jacking up your car is a crucial step in changing the fuel filter of your Peugeot 206. This step provides the necessary access and space to work underneath the vehicle. Here is a detailed guide on how to safely and effectively jack up your car or place it over an inspection pit:

First, ensure you have a suitable jack for your vehicle. The jack should be stable and strong enough to support the weight of your Peugeot 206. Place the jack on level ground, preferably on a concrete or paved surface, to ensure stability. Refer to your car's manual to locate the recommended jacking points on the car frame. These are typically found near the front or rear wheels, or both, and are often marked with a notch or indentation.

Once you have identified the jacking points, slowly raise the jack until it makes contact with the car's frame. Continue raising the jack until the car is lifted to the desired height. It is important to use jack stands for added safety, as they provide a secure and stable support for the vehicle. Place the jack stands at the recommended points and slowly lower the vehicle onto them. Ensure the car is securely resting on the stands before proceeding.

If you have access to an inspection pit, you can drive the car over it and position it so that the fuel filter is easily accessible from below. Make sure the vehicle is securely parked and will not roll or shift while you are working.

When the car is securely raised or positioned over the inspection pit, you can proceed to locate the fuel filter. It is usually found near the fuel tank or fuel pump, depending on the model of your Peugeot 206. Refer to your car's manual or seek advice from a trusted mechanic if you are unsure about the location.

Once you have identified the fuel filter, place a container underneath it to catch any fuel that may leak during the replacement process. This is an important safety measure to prevent fuel spills and potential fire hazards. Have your cleaning spray and fuel line pliers ready to begin the next steps of the fuel filter replacement process.

Prepare a container for fluids

Before you start, you'll need to prepare a container to catch any fluids that may leak out during the fuel filter replacement process. This is an important step to ensure that you don't end up with a messy workspace and to contain any fuel that may leak out.

It's recommended to use a container that is specifically designed for catching fluids, such as a drip pan or a drain pan. These containers typically have a capacity of around 4-8 litres and are made of durable materials that can withstand fluids like fuel, oil, and other automotive liquids. They often feature a spout or channel to help guide the fluids into the pan and away from the work area.

Alternatively, if you don't have access to a drip pan, you can use a large, sturdy plastic container or bucket. Make sure the container is clean and dry before placing it under the vehicle. Line the container with a plastic bag or absorbent material, such as old rags or paper towels, to help contain the fluids and make clean-up easier.

Once you have your container ready, place it under the vehicle, specifically under the fuel filter and fuel lines. This will catch any fuel that may leak out during the detachment process. It's important to note that working with fuel can be dangerous, so ensure adequate ventilation in your workspace and avoid any open flames or sparks.

Clean the fasteners of the fuel supply lines

To clean the fasteners of the fuel supply lines, you will need an all-purpose cleaning spray. This is an important step in the process of changing the fuel filter on a Peugeot 206 CC 2D or PEUGEOT 206 SW (2E/K).

Firstly, ensure you have adequate ventilation in your workspace as fuel vapours are poisonous. Next, to access the fuel supply lines, you will need to lift the car using a jack or place it over an inspection pit. Prepare a container for fluids that may leak from the filter housing and hoses.

Now, clean the fasteners of the fuel supply lines using the all-purpose cleaning spray. Once the fasteners are clean, you can remove the fuel lines from the car body. To do this, squeeze the clips and detach the fuel supply lines from the fuel filter housing using fuel line pliers and a crowbar.

It is important to be careful during this process as fuel may leak from the filter housing and hoses. Always dispose of used filters at special collection points to protect the environment from pollution.

Remove the fuel lines from the car body

To remove the fuel lines from the car body of a Peugeot 206, you will need fuel line pliers and a crowbar.

First, clean the fasteners of the fuel supply lines using an all-purpose cleaning spray. Next, squeeze the clips and detach the fuel supply lines from the fuel filter housing. You may need to use a crowbar to do this. Be careful, as fuel may leak from the filter housing and hoses.

If you are working on a Peugeot 206 SW (2E/K), you will need to use a chain oil filter wrench to loosen the fuel filter mounting before removing the fuel filter.

Remove and replace the fuel filter

The fuel filter on a Peugeot 206 is located under the bonnet, under the engine cover, in a plastic housing. To remove and replace the fuel filter, follow these steps:

Step 1: Prepare the Car

• Park the car on a level surface and engage the parking brake.
• Ensure the engine is switched off and allow it to cool down if it has been running recently.
• Unscrew the fuel filler cap to release pressure in the fuel system.
• Lift the car using a jack or place it over an inspection pit.
• Prepare a container to catch any spilled fluids.

Step 2: Remove the Old Fuel Filter

• Clean the fasteners of the fuel supply lines using an all-purpose cleaning spray.
• Remove the fuel lines from the car body.
• Squeeze the clips and detach the fuel supply lines from the fuel filter housing using fuel line pliers. Be careful, as fuel may leak from the housing and hoses.
• Remove the fuel filter using a crowbar and place the old filter cartridge in the container.

Step 3: Install the New Fuel Filter

• Install a new fuel filter, ensuring it is positioned correctly and considering the fuel flow direction mark.
• Connect the fuel supply lines to the new fuel filter, taking care to prevent dust and dirt from entering the fuel filter housing.
• Reinstall the fuel lines on the car body.
• Remove the fluid container from under the fuel filter.
• Tighten the fuel filler cap and close the fuel door.

Step 4: Final Checks

• Before starting the car, switch the ignition on and off several times to activate the fuel pump and pump fuel through the system.
• Run the engine for a few minutes to ensure the new fuel filter is operating correctly.
• Shut off the engine and dispose of the used filter at a special collection point to protect the environment from pollution.

Frequently asked questions